diff options
Diffstat (limited to 'rootdir/etc/init.qcom.usb.sh')
| -rwxr-xr-x | rootdir/etc/init.qcom.usb.sh | 65 |
1 files changed, 36 insertions, 29 deletions
diff --git a/rootdir/etc/init.qcom.usb.sh b/rootdir/etc/init.qcom.usb.sh index 1b2ba3a..e0e6f1d 100755 --- a/rootdir/etc/init.qcom.usb.sh +++ b/rootdir/etc/init.qcom.usb.sh @@ -93,42 +93,40 @@ fi target=`getprop ro.board.platform` +#ifdef VENDOR_EDIT +boot_mode=`getprop ro.boot.ftm_mode` +echo "boot_mode: $boot_mode" > /dev/kmsg +case "$boot_mode" in + "ftm_at" | "ftm_rf" | "ftm_wlan" | "ftm_mos") + usb_config=`getprop persist.sys.usb.config` + echo "BEFORE boot_mode: $usb_config" > /dev/kmsg + if [ "$usb_config" != "diag,adb" ] ; then + setprop persist.sys.usb.config diag,adb + fi + ;; +esac +usb_config=`getprop persist.sys.usb.config` +echo "AFTER boot_mode: $usb_config" > /dev/kmsg +#endif + # # Allow USB enumeration with default PID/VID # baseband=`getprop ro.baseband` echo 1 > /sys/class/android_usb/f_mass_storage/lun/nofua usb_config=`getprop persist.sys.usb.config` +echo "BEFORE: $usb_config" > /dev/kmsg case "$usb_config" in - "" | "adb") #USB persist config not set, select default configuration + "" | "adb" | "none") #USB persist config not set, select default configuration case "$esoc_link" in - "HSIC") - setprop persist.sys.usb.config diag,diag_mdm,serial_hsic,serial_tty,rmnet_hsic,mass_storage,adb - setprop persist.rmnet.mux enabled - ;; - "HSIC+PCIe") - setprop persist.sys.usb.config diag,diag_mdm,serial_hsic,rmnet_qti_ether,mass_storage,adb - ;; "PCIe") setprop persist.sys.usb.config diag,diag_mdm,serial_cdev,rmnet_qti_ether,mass_storage,adb ;; *) - case "$baseband" in - "mdm") - setprop persist.sys.usb.config mass_storage,adb - ;; - "mdm2") - setprop persist.sys.usb.config mass_storage,adb - ;; - "sglte") - setprop persist.sys.usb.config mass_storage,adb - ;; - "dsda" | "sglte2") - setprop persist.sys.usb.config mass_storage,adb - ;; - "dsda2") - setprop persist.sys.usb.config mass_storage,adb - ;; + case "$soc_hwplatform" in + "Dragon") + setprop persist.sys.usb.config diag,adb + ;; *) case "$target" in "msm8916") @@ -145,13 +143,18 @@ case "$usb_config" in if [ "$soc_revision" == "1.0" -o "$soc_hwplatform" == "Dragon" ] then setprop persist.sys.usb.config diag,adb - else - setprop persist.sys.usb.config diag,serial_cdev,serial_tty,rmnet_ipa,mass_storage,adb + #[BSP-66]-Anderson-Disable_set_the_property. + #This will ause BSP-66 issue and cause all the port enable in default. + #else + #setprop persist.sys.usb.config diag,serial_cdev,serial_tty,rmnet_ipa,mass_storage,adb fi ;; "msm8909" | "msm8937") setprop persist.sys.usb.config diag,serial_smd,rmnet_qti_bam,adb ;; + "msm8952" | "titanium") + setprop persist.sys.usb.config diag,serial_smd,rmnet_ipa,adb + ;; *) setprop persist.sys.usb.config diag,adb ;; @@ -160,10 +163,12 @@ case "$usb_config" in esac ;; esac - ;; - * ) ;; #USB persist config exists, do nothing + ;; + * ) ;; #USB persist config exists, do nothing esac + + # # Do target specific things # @@ -184,8 +189,10 @@ case "$target" in fi fi ;; - "msm8994" | "msm8992" | "msm8996") + "msm8994" | "msm8992" | "msm8996" | "titanium") echo BAM2BAM_IPA > /sys/class/android_usb/android0/f_rndis_qc/rndis_transports + echo 131072 > /sys/module/g_android/parameters/mtp_tx_req_len + echo 131072 > /sys/module/g_android/parameters/mtp_rx_req_len ;; esac |