summaryrefslogtreecommitdiff
path: root/drivers/s390/net (follow)
Commit message (Collapse)AuthorAge
* s390/qeth: don't process empty bridge port eventsJulian Wiedmann2020-08-21
| | | | | | | | | | | | | | [ Upstream commit 02472e28b9a45471c6d8729ff2c7422baa9be46a ] Discard events that don't contain any entries. This shouldn't happen, but subsequent code relies on being able to use entry 0. So better be safe than accessing garbage. Fixes: b4d72c08b358 ("qeth: bridgeport support - basic control") Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com> Reviewed-by: Alexandra Winter <wintera@linux.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
* s390/qeth: invoke softirqs after napi_schedule()Julian Wiedmann2019-11-25
| | | | | | | | | | | | | | | | | | | | [ Upstream commit 4d19db777a2f32c9b76f6fd517ed8960576cb43e ] Calling napi_schedule() from process context does not ensure that the NET_RX softirq is run in a timely fashion. So trigger it manually. This is no big issue with current code. A call to ndo_open() is usually followed by a ndo_set_rx_mode() call, and for qeth this contains a spin_unlock_bh(). Except for OSN, where qeth_l2_set_rx_mode() bails out early. Nevertheless it's best to not depend on this behaviour, and just fix the issue at its source like all other drivers do. For instance see commit 83a0c6e58901 ("i40e: Invoke softirqs after napi_reschedule"). Fixes: a1c3ed4c9ca0 ("qeth: NAPI support for l2 and l3 discipline") Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
* s390/qeth: fix VLAN attribute in bridge_hostnotify udev eventAlexandra Winter2019-07-10
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | [ Upstream commit 335726195e460cb6b3f795b695bfd31f0ea70ef0 ] Enabling sysfs attribute bridge_hostnotify triggers a series of udev events for the MAC addresses of all currently connected peers. In case no VLAN is set for a peer, the device reports the corresponding MAC addresses with VLAN ID 4096. This currently results in attribute VLAN=4096 for all non-VLAN interfaces in the initial series of events after host-notify is enabled. Instead, no VLAN attribute should be reported in the udev event for non-VLAN interfaces. Only the initial events face this issue. For dynamic changes that are reported later, the device uses a validity flag. This also changes the code so that it now sets the VLAN attribute for MAC addresses with VID 0. On Linux, no qeth interface will ever be registered with VID 0: Linux kernel registers VID 0 on all network interfaces initially, but qeth will drop .ndo_vlan_rx_add_vid for VID 0. Peers with other OSs could register MACs with VID 0. Fixes: 9f48b9db9a22 ("qeth: bridgeport support - address notifications") Signed-off-by: Alexandra Winter <wintera@linux.ibm.com> Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
* s390: ctcm: fix ctcm_new_device error return codeArnd Bergmann2019-05-16
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | [ Upstream commit 27b141fc234a3670d21bd742c35d7205d03cbb3a ] clang points out that the return code from this function is undefined for one of the error paths: ../drivers/s390/net/ctcm_main.c:1595:7: warning: variable 'result' is used uninitialized whenever 'if' condition is true [-Wsometimes-uninitialized] if (priv->channel[direction] == NULL) { ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ ../drivers/s390/net/ctcm_main.c:1638:9: note: uninitialized use occurs here return result; ^~~~~~ ../drivers/s390/net/ctcm_main.c:1595:3: note: remove the 'if' if its condition is always false if (priv->channel[direction] == NULL) { ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ ../drivers/s390/net/ctcm_main.c:1539:12: note: initialize the variable 'result' to silence this warning int result; ^ Make it return -ENODEV here, as in the related failure cases. gcc has a known bug in underreporting some of these warnings when it has already eliminated the assignment of the return code based on some earlier optimization step. Reviewed-by: Nathan Chancellor <natechancellor@gmail.com> Signed-off-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
* s390/qeth: fix use-after-free in error pathJulian Wiedmann2019-03-23
| | | | | | | | | | | | | | | | | [ Upstream commit afa0c5904ba16d59b0454f7ee4c807dae350f432 ] The error path in qeth_alloc_qdio_buffers() that takes care of cleaning up the Output Queues is buggy. It first frees the queue, but then calls qeth_clear_outq_buffers() with that very queue struct. Make the call to qeth_clear_outq_buffers() part of the free action (in the correct order), and while at it fix the naming of the helper. Fixes: 0da9581ddb0f ("qeth: exploit asynchronous delivery of storage blocks") Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com> Reviewed-by: Alexandra Winter <wintera@linux.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
* s390/qeth: fix length check in SNMP processingJulian Wiedmann2018-12-13
| | | | | | | | | | | | | | | | | | | | | [ Upstream commit 9a764c1e59684c0358e16ccaafd870629f2cfe67 ] The response for a SNMP request can consist of multiple parts, which the cmd callback stages into a kernel buffer until all parts have been received. If the callback detects that the staging buffer provides insufficient space, it bails out with error. This processing is buggy for the first part of the response - while it initially checks for a length of 'data_len', it later copies an additional amount of 'offsetof(struct qeth_snmp_cmd, data)' bytes. Fix the calculation of 'data_len' for the first part of the response. This also nicely cleans up the memcpy code. Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2") Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com> Reviewed-by: Ursula Braun <ubraun@linux.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* s390/qeth: don't dump past end of unknown HW headerJulian Wiedmann2018-10-10
| | | | | | | | | | | | | | [ Upstream commit 0ac1487c4b2de383b91ecad1be561b8f7a2c15f4 ] For inbound data with an unsupported HW header format, only dump the actual HW header. We have no idea how much payload follows it, and what it contains. Worst case, we dump past the end of the Inbound Buffer and access whatever is located next in memory. Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* s390/qeth: reset layer2 attribute on layer switchJulian Wiedmann2018-09-26
| | | | | | | | | | | | | | | | | | | [ Upstream commit 70551dc46ffa3555a0b5f3545b0cd87ab67fd002 ] After the subdriver's remove() routine has completed, the card's layer mode is undetermined again. Reflect this in the layer2 field. If qeth_dev_layer2_store() hits an error after remove() was called, the card _always_ requires a setup(), even if the previous layer mode is requested again. But qeth_dev_layer2_store() bails out early if the requested layer mode still matches the current one. So unless we reset the layer2 field, re-probing the card back to its previous mode is currently not possible. Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* s390/qeth: fix race in used-buffer accountingJulian Wiedmann2018-09-26
| | | | | | | | | | | | | | [ Upstream commit a702349a4099cd5a7bab0904689d8e0bf8dcd622 ] By updating q->used_buffers only _after_ do_QDIO() has completed, there is a potential race against the buffer's TX completion. In the unlikely case that the TX completion path wins, qeth_qdio_output_handler() would decrement the counter before qeth_flush_buffers() even incremented it. Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* s390/qeth: on channel error, reject further cmd requestsJulian Wiedmann2018-03-31
| | | | | | | | | | | | | | | | | | | [ Upstream commit a6c3d93963e4b333c764fde69802c3ea9eaa9d5c ] When the IRQ handler determines that one of the cmd IO channels has failed and schedules recovery, block any further cmd requests from being submitted. The request would inevitably stall, and prevent the recovery from making progress until the request times out. This sort of error was observed after Live Guest Relocation, where the pending IO on the READ channel intentionally gets terminated to kick-start recovery. Simultaneously the guest executed SIOCETHTOOL, triggering qeth to issue a QUERY CARD INFO command. The command then stalled in the inoperabel WRITE channel. Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* s390/qeth: lock read device while queueing next bufferJulian Wiedmann2018-03-31
| | | | | | | | | | | | | | [ Upstream commit 17bf8c9b3d499d5168537c98b61eb7a1fcbca6c2 ] For calling ccw_device_start(), issue_next_read() needs to hold the device's ccwlock. This is satisfied for the IRQ handler path (where qeth_irq() gets called under the ccwlock), but we need explicit locking for the initial call by the MPC initialization. Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* s390/qeth: when thread completes, wake up all waitersJulian Wiedmann2018-03-31
| | | | | | | | | | | | | [ Upstream commit 1063e432bb45be209427ed3f1ca3908e4aa3c7d7 ] qeth_wait_for_threads() is potentially called by multiple users, make sure to notify all of them after qeth_clear_thread_running_bit() adjusted the thread_running_mask. With no timeout, callers would otherwise stall. Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* s390/qeth: free netdevice when removing a cardJulian Wiedmann2018-03-31
| | | | | | | | | | | | | | | | | | | | | | | | | | | [ Upstream commit 6be687395b3124f002a653c1a50b3260222b3cd7 ] On removal, a qeth card's netdevice is currently not properly freed because the call chain looks as follows: qeth_core_remove_device(card) lx_remove_device(card) unregister_netdev(card->dev) card->dev = NULL !!! qeth_core_free_card(card) if (card->dev) !!! free_netdev(card->dev) Fix it by free'ing the netdev straight after unregistering. This also fixes the sysfs-driven layer switch case (qeth_dev_layer2_store()), where the need to free the current netdevice was not considered at all. Note that free_netdev() takes care of the netif_napi_del() for us too. Fixes: 4a71df50047f ("qeth: new qeth device driver") Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com> Reviewed-by: Ursula Braun <ubraun@linux.vnet.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* s390/qeth: fix IPA command submission raceJulian Wiedmann2018-03-11
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | [ Upstream commit d22ffb5a712f9211ffd104c38fc17cbfb1b5e2b0 ] If multiple IPA commands are build & sent out concurrently, fill_ipacmd_header() may assign a seqno value to a command that's different from what send_control_data() later assigns to this command's reply. This is due to other commands passing through send_control_data(), and incrementing card->seqno.ipa along the way. So one IPA command has no reply that's waiting for its seqno, while some other IPA command has multiple reply objects waiting for it. Only one of those waiting replies wins, and the other(s) times out and triggers a recovery via send_ipa_cmd(). Fix this by making sure that the same seqno value is assigned to a command and its reply object. Do so immediately before submitting the command & while holding the irq_pending "lock", to produce nicely ascending seqnos. As a side effect, *all* IPA commands now use a reply object that's waiting for its actual seqno. Previously, early IPA commands that were submitted while the card was still DOWN used the "catch-all" IDX seqno. Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* s390/qeth: fix SETIP command handlingJulian Wiedmann2018-03-11
| | | | | | | | | | | | | [ Upstream commit 1c5b2216fbb973a9410e0b06389740b5c1289171 ] send_control_data() applies some special handling to SETIP v4 IPA commands. But current code parses *all* command types for the SETIP command code. Limit the command code check to IPA commands. Fixes: 5b54e16f1a54 ("qeth: do not spin for SETIP ip assist command") Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* s390/qeth: no ETH header for outbound AF_IUCVJulian Wiedmann2017-12-25
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | [ Upstream commit acd9776b5c45ef02d1a210969a6fcc058afb76e3 ] With AF_IUCV traffic, the skb passed to hard_start_xmit() has a 14 byte slot at skb->data, intended for an ETH header. qeth_l3_fill_af_iucv_hdr() fills this ETH header... and then immediately moves it to the skb's headroom, where it disappears and is never seen again. But it's still possible for us to return NETDEV_TX_BUSY after the skb has been modified. Since we didn't get a private copy of the skb, the next time the skb is delivered to hard_start_xmit() it no longer has the expected layout (we moved the ETH header to the headroom, so skb->data now starts at the IUCV_TRANS header). So when qeth_l3_fill_af_iucv_hdr() does another round of rebuilding, the resulting qeth header ends up all wrong. On transmission, the buffer is then rejected by the HiperSockets device with SBALF15 = x'04'. When this error is passed back to af_iucv as TX_NOTIFY_UNREACHABLE, it tears down the offending socket. As the ETH header for AF_IUCV serves no purpose, just align the code to what we do for IP traffic on L3 HiperSockets: keep the ETH header at skb->data, and pass down data_offset = ETH_HLEN to qeth_fill_buffer(). When mapping the payload into the SBAL elements, the ETH header is then stripped off. This avoids the skb manipulations in qeth_l3_fill_af_iucv_hdr(), and any buffer re-entering hard_start_xmit() after NETDEV_TX_BUSY is now processed properly. Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com> Signed-off-by: Ursula Braun <ubraun@linux.vnet.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <alexander.levin@verizon.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* s390/qeth: issue STARTLAN as first IPA commandJulian Wiedmann2017-11-15
| | | | | | | | | | | | | | | | | | [ Upstream commit 1034051045d125579ab1e8fcd5a724eeb0e70149 ] STARTLAN needs to be the first IPA command after MPC initialization completes. So move the qeth_send_startlan() call from the layer disciplines into the core path, right after the MPC handshake. While at it, replace the magic LAN OFFLINE return code with the existing enum. Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com> Reviewed-by: Thomas Richter <tmricht@linux.vnet.ibm.com> Reviewed-by: Ursula Braun <ubraun@linux.vnet.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <alexander.levin@verizon.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* s390/qeth: avoid null pointer dereference on OSNJulian Wiedmann2017-06-07
| | | | | | | | | | | [ Upstream commit 25e2c341e7818a394da9abc403716278ee646014 ] Access card->dev only after checking whether's its valid. Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com> Reviewed-by: Ursula Braun <ubraun@linux.vnet.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* s390/qeth: unbreak OSM and OSN supportJulian Wiedmann2017-06-07
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | [ Upstream commit 2d2ebb3ed0c6acfb014f98e427298673a5d07b82 ] commit b4d72c08b358 ("qeth: bridgeport support - basic control") broke the support for OSM and OSN devices as follows: As OSM and OSN are L2 only, qeth_core_probe_device() does an early setup by loading the l2 discipline and calling qeth_l2_probe_device(). In this context, adding the l2-specific bridgeport sysfs attributes via qeth_l2_create_device_attributes() hits a BUG_ON in fs/sysfs/group.c, since the basic sysfs infrastructure for the device hasn't been established yet. Note that OSN actually has its own unique sysfs attributes (qeth_osn_devtype), so the additional attributes shouldn't be created at all. For OSM, add a new qeth_l2_devtype that contains all the common and l2-specific sysfs attributes. When qeth_core_probe_device() does early setup for OSM or OSN, assign the corresponding devtype so that the ccwgroup probe code creates the full set of sysfs attributes. This allows us to skip qeth_l2_create_device_attributes() in case of an early setup. Any device that can't do early setup will initially have only the generic sysfs attributes, and when it's probed later qeth_l2_probe_device() adds the l2-specific attributes. If an early-setup device is removed (by calling ccwgroup_ungroup()), device_unregister() will - using the devtype - delete the l2-specific attributes before qeth_l2_remove_device() is called. So make sure to not remove them twice. What complicates the issue is that qeth_l2_probe_device() and qeth_l2_remove_device() is also called on a device when its layer2 attribute changes (ie. its layer mode is switched). For early-setup devices this wouldn't work properly - we wouldn't remove the l2-specific attributes when switching to L3. But switching the layer mode doesn't actually make any sense; we already decided that the device can only operate in L2! So just refuse to switch the layer mode on such devices. Note that OSN doesn't have a layer2 attribute, so we only need to special-case OSM. Based on an initial patch by Ursula Braun. Fixes: b4d72c08b358 ("qeth: bridgeport support - basic control") Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* s390/qeth: handle sysfs error during initializationUrsula Braun2017-06-07
| | | | | | | | | | | | | | | [ Upstream commit 9111e7880ccf419548c7b0887df020b08eadb075 ] When setting up the device from within the layer discipline's probe routine, creating the layer-specific sysfs attributes can fail. Report this error back to the caller, and handle it by releasing the layer discipline. Signed-off-by: Ursula Braun <ubraun@linux.vnet.ibm.com> [jwi: updated commit msg, moved an OSN change to a subsequent patch] Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* qeth: initialize net_device with carrier offUrsula Braun2016-09-15
| | | | | | | | | | | | | | | | | | [ Upstream commit e5ebe63214d44d4dcf43df02edf3613e04d671b9 ] /sys/class/net/<interface>/operstate for an active qeth network interface offen shows "unknown", which translates to "state UNKNOWN in output of "ip link show". It is caused by a missing initialization of the __LINK_STATE_NOCARRIER bit in the net_device state field. This patch adds a netif_carrier_off() invocation when creating the net_device for a qeth device. Signed-off-by: Ursula Braun <ubraun@linux.vnet.ibm.com> Acked-by: Hendrik Brueckner <brueckner@linux.vnet.ibm.com> Reference-ID: Bugzilla 133209 Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <alexander.levin@verizon.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* qeth: delete napi struct when removing a qeth deviceUrsula Braun2016-08-10
| | | | | | | | | | | | | | | | commit 7831b4ff0d926e0deeaabef9db8800ed069a2757 upstream. A qeth_card contains a napi_struct linked to the net_device during device probing. This struct must be deleted when removing the qeth device, otherwise Panic on oops can occur when qeth devices are repeatedly removed and added. Fixes: a1c3ed4c9ca ("qeth: NAPI support for l2 and l3 discipline") Signed-off-by: Ursula Braun <ubraun@linux.vnet.ibm.com> Tested-by: Alexander Klein <ALKL@de.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* s390/qeth: optimize MAC handling in rx_mode callbackLakhvich Dmitriy2015-10-07
| | | | | | | | | | | | | | | | | | | | | In layer2 mode of the qeth driver, MAC address lists from struct net_device require mapping to the OSA-card. The existing implementation is inefficient for lists with more than several MAC addresses, since for every ndo_set_rx_mode callback it removes all MAC addresses first, and then registers the current MAC address list. This patch changes implementation of ndo_set_rx_mode callback in qeth, only performing hardware registration/removal for new/deleted addresses. To shorten lookup of MAC addresses registered addresses are kept in a hashtable instead of a linear list. Signed-off-by: Lakhvich Dmitriy <ldmitriy@ru.ibm.com> Signed-off-by: Ursula Braun <ursula.braun@de.ibm.com> Reviewed-by: Eugene Crosser <Eugene.Crosser@ru.ibm.com> Reviewed-by: Thomas Richter <tmricht@de.ibm.com> Tested-by: Christian Borntraeger <borntraeger@de.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* s390/qeth: switch to napi_gro_receiveThomas Richter2015-10-07
| | | | | | | | | | Add support for GRO (generic receive offload) in the layer 2 part of device driver qeth. This results in a performance improvement when GRO and RX is turned on. Signed-off-by: Thomas Richter <tmricht@linux.vnet.ibm.com> Signed-off-by: Ursula Braun <ursula.braun@de.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* s390/iucv: do not use arrays as argumentUrsula Braun2015-09-21
| | | | | | | | | | The iucv code uses arrays as arguments. Even though this does not really cause a problem, it could be misleading, since the compiler turns array arguments into just a pointer argument. To be more precise this patch changes the array arguments into pointers. Signed-off-by: Ursula Braun <ursula.braun@de.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* qeth: add layer 2 RX/TX checksum offloadingThomas Richter2015-09-21
| | | | | | | | | | | | | | | | | | | | | Checksum offloading for send and receive is already supported for layer 3 (IP layer). This patch adds support for RX and TX hardware checksum offloading for layer 2 (MAC layer). The hardware calculates the checksum for IP UDP and TCP packets. This patch moves the hardware checksum offloading setup to the set of common functions in qeth_core_main.c. Layer 2 and layer 3 now simply call the same common functions. Also note that TX checksum offloading is always enabled. The device driver relies on the TCP/IP stack to make use of this feature. Signed-off-by: Thomas Richter <tmricht@linux.vnet.ibm.com> Signed-off-by: Ursula Braun <ursula.braun@de.ibm.com> Reviewed-by: Eugene Crosser <Eugene.Crosser@ru.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* qeth: move OSA portname into deprecated statusUrsula Braun2015-09-21
| | | | | | | | | An OSA-Express port name was required to identify a shared OSA port. All operating system instances that shared the port had to use the same port name. This requirement no longer applies. Signed-off-by: Ursula Braun <ursula.braun@de.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* qeth: no write permission for readonly sysattrLakhvich Dmitriy2015-09-21
| | | | | | | | | | | | User is not allowed to write into bridge_state sysfs file. Fixed attribute not mislead the user Signed-off-by: Lakhvich Dmitriy <ldmitriy@ru.ibm.com> Signed-off-by: Ursula Braun <ursula.braun@de.ibm.com> Reported-by: Peter Oberparleiter <oberpar@linux.vnet.ibm.com> Reviewed-by: Eugene Crosser <Eugene.Crosser@ru.ibm.com> Reviewed-by: Thomas Richter <tmricht@de.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* qeth: remove extraneous length from %pM formatEugene Crosser2015-09-21
| | | | | | | | | | Length specifier in the %pM format is not supported (at least, not documented). Remove it, and also an extraneous '&' for the array. Signed-off-by: Eugene Crosser <Eugene.Crosser@ru.ibm.com> Signed-off-by: Ursula Braun <ursula.braun@de.ibm.com> Suggested-by: Joe Perches <joe@perches.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* s390: remove unneeded variablesPeter Senna Tschudin2015-08-07
| | | | | | | | | | | | | This patch remove unneeded variables used to store return values. These issues were detected with the Coccinelle script: scripts/coccinelle/misc/returnvar.cocci [heiko.carstens@de.ibm.com]: make qeth_l[2/3]_stop() return void Signed-off-by: Peter Senna Tschudin <peter.senna@gmail.com> Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com> Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
* s390/lcs: Fix null-pointer access in msgPeter Oberparleiter2015-05-18
| | | | | | | | | | | | | | | | | An attempt to configure a CTC device as LCS results in the following error message: (null): Detecting a network adapter for LCS devices failed with rc=-5 (0xfffffffb) "(null)" results from access to &card->dev->dev in lcs_new_device() which is only initialized later in the function. Fix this by using &ccwgdev->dev instead which is initialized before lcs_new_device() is called. Signed-off-by: Peter Oberparleiter <oberpar@linux.vnet.ibm.com> Signed-off-by: Ursula Braun <ursula.braun@de.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* qeth: replace ENOSYS with EOPNOTSUPPEugene Crosser2015-05-18
| | | | | | | | | | | Since recently, `checkpatch.pl` advices that ENOSYS should not be used for anything other than "invalid syscall nr". This patch replaces ENOSYS return code with EOPNOTSUPP for the "unsupported function" conditions. Signed-off-by: Eugene Crosser <Eugene.Crosser@ru.ibm.com> Signed-off-by: Ursula Braun <ursula.braun@de.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* qeth: BRIDGEPORT "sanity check"Eugene Crosser2015-05-18
| | | | | | | | | | | Forbid enabling IFF_PROMISC reflection to BRIDGEPORT when a role is already assigned, and forbid direct manipulation of the role when reflection mode is engaged. Reviewed-by: Thomas Richter <tmricht@linux.vnet.ibm.com> Signed-off-by: Eugene Crosser <Eugene.Crosser@ru.ibm.com> Signed-off-by: Ursula Braun <ursula.braun@de.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* qeth: OSA version of SETBRIDGEPORT commandEugene Crosser2015-05-18
| | | | | | | | | | | | OSA Ethernet hardware is introducing BRIDGEPORT functionality similar (but not identical) to HiperSockets BRIDGEPORT. This patch makes HiperSockets BRIDGEPORT related sysfs attributes and udev events work with OSA hardware too. Reviewed-by: Thomas Richter <tmricht@linux.vnet.ibm.com> Signed-off-by: Eugene Crosser <Eugene.Crosser@ru.ibm.com> Signed-off-by: Ursula Braun <ursula.braun@de.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* qeth: IFF_PROMISC flag to BRIDGE PORT modeEugene Crosser2015-05-18
| | | | | | | | | | | | | | OSA and HiperSocket devices do not support promiscuous mode proper, but they support "BRIDGE PORT" mode that is functionally similar. This update introduces sysfs attribute that, when set, makes the driver try to "reflect" setting and resetting of the IFF_PROMISC flag on the interface into setting and resetting PRIMARY or SECONDARY bridge port role on the underlying OSA or HiperSocket device. Reviewed-by: Thomas Richter <tmricht@linux.vnet.ibm.com> Signed-off-by: Eugene Crosser <Eugene.Crosser@ru.ibm.com> Signed-off-by: Ursula Braun <ursula.braun@de.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* qeth: remove locks from sysfs _showEugene Crosser2015-05-18
| | | | | | | | | | | Locking is probably unnecessary in this case, and the rest of the qeth sysfs code does not use locks in the *_show() functions. Remove locks from the layer2 *_show() functions in which they where accidentally introduced. Signed-off-by: Eugene Crosser <Eugene.Crosser@ru.ibm.com> Signed-off-by: Ursula Braun <ursula.braun@de.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* qeth: fix handling of IPA return codesEugene Crosser2015-05-18
| | | | | | | | | | Function that executes IPA commands returns the result code from the IPA response block. If non-negative, it needs to be transformed into errno-compatible code before returning to the caller. Signed-off-by: Eugene Crosser <Eugene.Crosser@ru.ibm.com> Signed-off-by: Ursula Braun <ursula.braun@de.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* qeth: fix rx checksum offload handlingThomas Richter2015-05-18
| | | | | | | | | | | | | | | | | | | ethtool is used to change some device driver features such as RX/TX hardware checksum offloading. The qeth device driver callback function to turn on/off RX hardware check sum handling never changes the hardware configuration. The NETIF_F_RXCSUM bit is cleared when the feature bitset type netdev_features_t(64bit) is assigned to 32 a bit variable. This patch fixes the NETIF_F_RXCSUM handling. Also there is no need to manipulate the device's features bit set as this is done by the caller when no error occurs. Signed-off-by: Thomas Richter <tmricht@linux.vnet.ibm.com> Signed-off-by: Ursula Braun <ursula.braun@de.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-nextLinus Torvalds2015-04-15
|\ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Pull networking updates from David Miller: 1) Add BQL support to via-rhine, from Tino Reichardt. 2) Integrate SWITCHDEV layer support into the DSA layer, so DSA drivers can support hw switch offloading. From Floria Fainelli. 3) Allow 'ip address' commands to initiate multicast group join/leave, from Madhu Challa. 4) Many ipv4 FIB lookup optimizations from Alexander Duyck. 5) Support EBPF in cls_bpf classifier and act_bpf action, from Daniel Borkmann. 6) Remove the ugly compat support in ARP for ugly layers like ax25, rose, etc. And use this to clean up the neigh layer, then use it to implement MPLS support. All from Eric Biederman. 7) Support L3 forwarding offloading in switches, from Scott Feldman. 8) Collapse the LOCAL and MAIN ipv4 FIB tables when possible, to speed up route lookups even further. From Alexander Duyck. 9) Many improvements and bug fixes to the rhashtable implementation, from Herbert Xu and Thomas Graf. In particular, in the case where an rhashtable user bulk adds a large number of items into an empty table, we expand the table much more sanely. 10) Don't make the tcp_metrics hash table per-namespace, from Eric Biederman. 11) Extend EBPF to access SKB fields, from Alexei Starovoitov. 12) Split out new connection request sockets so that they can be established in the main hash table. Much less false sharing since hash lookups go direct to the request sockets instead of having to go first to the listener then to the request socks hashed underneath. From Eric Dumazet. 13) Add async I/O support for crytpo AF_ALG sockets, from Tadeusz Struk. 14) Support stable privacy address generation for RFC7217 in IPV6. From Hannes Frederic Sowa. 15) Hash network namespace into IP frag IDs, also from Hannes Frederic Sowa. 16) Convert PTP get/set methods to use 64-bit time, from Richard Cochran. * git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1816 commits) fm10k: Bump driver version to 0.15.2 fm10k: corrected VF multicast update fm10k: mbx_update_max_size does not drop all oversized messages fm10k: reset head instead of calling update_max_size fm10k: renamed mbx_tx_dropped to mbx_tx_oversized fm10k: update xcast mode before synchronizing multicast addresses fm10k: start service timer on probe fm10k: fix function header comment fm10k: comment next_vf_mbx flow fm10k: don't handle mailbox events in iov_event path and always process mailbox fm10k: use separate workqueue for fm10k driver fm10k: Set PF queues to unlimited bandwidth during virtualization fm10k: expose tx_timeout_count as an ethtool stat fm10k: only increment tx_timeout_count in Tx hang path fm10k: remove extraneous "Reset interface" message fm10k: separate PF only stats so that VF does not display them fm10k: use hw->mac.max_queues for stats fm10k: only show actual queues, not the maximum in hardware fm10k: allow creation of VLAN on default vid fm10k: fix unused warnings ...
| * qeth: Fix command sizesStefan Raspl2015-02-28
| | | | | | | | | | | | | | | | | | | | This patch adjusts two instances where we were using the (too big) struct qeth_ipacmd_setadpparms size instead of the commands' actual size. This didn't do any harm, but wasted a few bytes. Signed-off-by: Stefan Raspl <raspl@linux.vnet.ibm.com> Signed-off-by: Ursula Braun <ursula.braun@de.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
| * s390: remove claw driverUrsula Braun2015-02-28
| | | | | | | | | | | | | | | | claw devices are outdated and no longer supported. This patch removes the claw driver. Signed-off-by: Ursula Braun <ursula.braun@de.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* | s390: remove 31 bit supportHeiko Carstens2015-03-25
|/ | | | | | | | | | | | | | | | | | | Remove the 31 bit support in order to reduce maintenance cost and effectively remove dead code. Since a couple of years there is no distribution left that comes with a 31 bit kernel. The 31 bit kernel also has been broken since more than a year before anybody noticed. In addition I added a removal warning to the kernel shown at ipl for 5 minutes: a960062e5826 ("s390: add 31 bit warning message") which let everybody know about the plan to remove 31 bit code. We didn't get any response. Given that the last 31 bit only machine was introduced in 1999 let's remove the code. Anybody with 31 bit user space code can still use the compat mode. Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com> Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
* Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/netDavid S. Miller2015-01-27
|\ | | | | | | | | | | | | | | | | | | Conflicts: arch/arm/boot/dts/imx6sx-sdb.dts net/sched/cls_bpf.c Two simple sets of overlapping changes. Signed-off-by: David S. Miller <davem@davemloft.net>
| * 390/qeth: Fix locking warning during qeth device setupThomas Richter2015-01-25
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Do not wait for channel command buffers in IPA commands. The potential wait could be done while holding a spin lock and causes in recent kernels such a bug if kernel lock debugging is enabled: kernel: BUG: sleeping function called from invalid context at drivers/s390/net/qeth_core_main.c: 794 kernel: in_atomic(): 1, irqs_disabled(): 0, pid: 2031, name: NetworkManager kernel: 2 locks held by NetworkManager/2031: kernel: #0: (rtnl_mutex){+.+.+.}, at: [<00000000006e0d7a>] rtnetlink_rcv+0x32/0x50 kernel: #1: (_xmit_ETHER){+.....}, at: [<00000000006cfe90>] dev_set_rx_mode+0x30/0x50 kernel: CPU: 0 PID: 2031 Comm: NetworkManager Not tainted 3.18.0-rc5-next-20141124 #1 kernel: 00000000275fb1f0 00000000275fb280 0000000000000002 0000000000000000 00000000275fb320 00000000275fb298 00000000275fb298 00000000007e326a 0000000000000000 000000000099ce2c 00000000009b4988 000000000000000b 00000000275fb2e0 00000000275fb280 0000000000000000 0000000000000000 0000000000000000 00000000001129c8 00000000275fb280 00000000275fb2e0 kernel: Call Trace: kernel: ([<00000000001128b0>] show_trace+0xf8/0x158) kernel: [<000000000011297a>] show_stack+0x6a/0xe8 kernel: [<00000000007e995a>] dump_stack+0x82/0xb0 kernel: [<000000000017d668>] ___might_sleep+0x170/0x228 kernel: [<000003ff80026f0e>] qeth_wait_for_buffer+0x36/0xd0 [qeth] kernel: [<000003ff80026fe2>] qeth_get_ipacmd_buffer+0x3a/0xc0 [qeth] kernel: [<000003ff80105078>] qeth_l3_send_setdelmc+0x58/0xf8 [qeth_l3] kernel: [<000003ff8010b1fe>] qeth_l3_set_ip_addr_list+0x2c6/0x848 [qeth_l3] kernel: [<000003ff8010bbb4>] qeth_l3_set_multicast_list+0x434/0xc48 [qeth_l3] kernel: [<00000000006cfe9a>] dev_set_rx_mode+0x3a/0x50 kernel: [<00000000006cff90>] __dev_open+0xe0/0x140 kernel: [<00000000006d02a0>] __dev_change_flags+0xa0/0x178 kernel: [<00000000006d03a8>] dev_change_flags+0x30/0x70 kernel: [<00000000006e14ee>] do_setlink+0x346/0x9a0 ... The device driver has plenty of command buffers available per channel for channel command communication. In the extremely rare case when there is no command buffer available, return a NULL pointer and issue a warning in the kernel log. The caller handles the case when a NULL pointer is encountered and returns an error. In the case the wait for command buffer is possible (because no lock is held as in the OSN case), still wait until a channel command buffer is available. Signed-off-by: Thomas Richter <tmricht@linux.vnet.ibm.com> Signed-off-by: Ursula Braun <ursula.braun@de.ibm.com> Reviewed-by: Eugene Crosser <Eugene.Crosser@ru.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
| * qeth: clean up error handlingEugene Crosser2015-01-25
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | In the functions that are registering and unregistering MAC addresses in the qeth-handled hardware, remove callback functions that are unnesessary, as only the return code is analyzed. Translate hardware response codes to semi-standard 'errno'-like codes for readability. Add kernel-doc description to the internal API function qeth_send_control_data(). Signed-off-by: Eugene Crosser <Eugene.Crosser@ru.ibm.com> Signed-off-by: Ursula Braun <ursula.braun@de.ibm.com> Reviewed-by: Thomas-Mich Richter <tmricht@linux.vnet.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* | qeth: Remove unneeded structure memberThomas Richter2015-01-17
| | | | | | | | | | | | | | | | | | | | The member irq_tasklet in the qeth_channel structure is not referenced anymore and is removed from the structure. Signed-off-by: Thomas Richter <tmricht@linux.vnet.ibm.com> Signed-off-by: Ursula Braun <ursula.braun@de.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* | qeth: sysfs: replace strcmp() with sysfs_streq()Eugene Crosser2015-01-17
| | | | | | | | | | | | | | | | | | | | | | Replace combination of strsep() and a temporary char * followed by a series of "if (!strcmp(...))" with a series of "if (sysfs_streq(...))". Signed-off-by: Eugene Crosser <Eugene.Crosser@ru.ibm.com> Signed-off-by: Ursula Braun <ursula.braun@de.ibm.com> Reviewed-by: Thomas-Mich Richter <tmricht@de.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* | qeth: use qeth_card_hw_is_reachable() everywhereEugene Crosser2015-01-17
| | | | | | | | | | | | | | | | | | | | | | qeth_card_hw_is_reachable() was introduced as part of a new functionality, but it is a useful abstraction that can replace verbose checks througout the rest of the `qeth` driver. Signed-off-by: Eugene Crosser <Eugene.Crosser@ru.ibm.com> Signed-off-by: Ursula Braun <ursula.braun@de.ibm.com> Reviewed-by: Thomas-Mich Richter <tmricht@de.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* | s390/net: Delete useless checks before function callsMarkus Elfring2015-01-17
| | | | | | | | | | | | | | | | | | | | | | | | The function debug_unregister() tests whether its argument is NULL and then returns immediately. Thus the test around the call is not needed. This issue was detected by using the Coccinelle software. Signed-off-by: Markus Elfring <elfring@users.sourceforge.net> Signed-off-by: Ursula Braun <ursula.braun@de.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* | s390/ctcm, netiucv: migrate variables to handle y2038 problemAya Mahfouz2015-01-17
| | | | | | | | | | | | | | | | | | | | | | | | This patch is concerned with migrating the time variables for the s390 network drivers. The changes handle the y2038 problem where timespec will overflow in the year 2038. timespec was replaced by unsigned long and all time variables get their values from the jiffies global variable. This was done for the sake of speed and efficiency. Signed-off-by: Aya Mahfouz <mahfouz.saif.elyazal@gmail.com> Signed-off-by: Ursula Braun <ursula.braun@de.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
generated by cgit v1.2.3 (git 2.25.1) at 2026-01-24 15:59:13 +0000