diff options
| -rw-r--r-- | drivers/staging/Kconfig | 2 | ||||
| -rw-r--r-- | drivers/staging/Makefile | 1 | ||||
| -rw-r--r-- | drivers/staging/qcacld-2.0/Android.mk | 156 | ||||
| -rwxr-xr-x | drivers/staging/qcacld-2.0/firmware_bin/WCNSS_cfg.dat | bin | 10234 -> 0 bytes | |||
| -rwxr-xr-x | drivers/staging/qcacld-2.0/firmware_bin/WCNSS_qcom_cfg.ini | 686 | ||||
| -rw-r--r-- | drivers/staging/qcacld-2.0/firmware_bin/WCNSS_qcom_cfg.usb.ini | 567 |
6 files changed, 3 insertions, 1409 deletions
diff --git a/drivers/staging/Kconfig b/drivers/staging/Kconfig index 5d3b86a33857..5eec85d4c9c5 100644 --- a/drivers/staging/Kconfig +++ b/drivers/staging/Kconfig @@ -110,4 +110,6 @@ source "drivers/staging/wilc1000/Kconfig" source "drivers/staging/most/Kconfig" +source "drivers/staging/qcacld-2.0/Kconfig" + endif # STAGING diff --git a/drivers/staging/Makefile b/drivers/staging/Makefile index 654ee8d54096..b3fcd1fceae8 100644 --- a/drivers/staging/Makefile +++ b/drivers/staging/Makefile @@ -46,3 +46,4 @@ obj-$(CONFIG_FB_TFT) += fbtft/ obj-$(CONFIG_FSL_MC_BUS) += fsl-mc/ obj-$(CONFIG_WILC1000) += wilc1000/ obj-$(CONFIG_MOST) += most/ +obj-$(CONFIG_QCA_CLD_WLAN) += qcacld-2.0/ diff --git a/drivers/staging/qcacld-2.0/Android.mk b/drivers/staging/qcacld-2.0/Android.mk deleted file mode 100644 index 35f0fe927a70..000000000000 --- a/drivers/staging/qcacld-2.0/Android.mk +++ /dev/null @@ -1,156 +0,0 @@ -# Android makefile for the WLAN Module - -# Assume no targets will be supported -WLAN_CHIPSET := - -ifeq ($(BOARD_HAS_QCOM_WLAN), true) -# Build/Package options for 8084/8092/8960/8992/8994/msm8996 targets -ifeq ($(call is-board-platform-in-list, apq8084 mpq8092 msm8952 msm8960 msm8992 msm8994 msm8996),true) -WLAN_CHIPSET := qca_cld -WLAN_SELECT := CONFIG_QCA_CLD_WLAN=m -endif - -# Build/Package options for 8953_som/8909_som target -ifeq ($(call is-board-platform-in-list, msm8953 msm8909),true) -ifeq ($(SD624_SOM_SUPPORT), true) -WLAN_CHIPSET := qca_cld -WLAN_SELECT := CONFIG_QCA_CLD_WLAN=m -endif -ifeq ($(SD212_SOM_SUPPORT), true) -WLAN_CHIPSET := qca_cld -WLAN_SELECT := CONFIG_QCA_CLD_WLAN=m -endif -endif - -# Build/Package only in case of supported target -ifneq ($(WLAN_CHIPSET),) - -# Check for kernel version -ifeq ($(TARGET_KERNEL_VERSION),) -$(info "WLAN: TARGET_KERNEL_VERSION not defined, assuming default") -TARGET_KERNEL_VERSION := 3.18 -TARGET_KERNEL_SOURCE := kernel -KERNEL_TO_BUILD_ROOT_OFFSET := ../ -endif - -# Check for supported kernel -ifeq ($(TARGET_KERNEL_VERSION),$(filter $(TARGET_KERNEL_VERSION),4.4 3.18)) -$(info "WLAN: supported kernel detected, building qcacld-2.0") - -# If kernel path offset is not defined, assume old kernel structure -ifeq ($(KERNEL_TO_BUILD_ROOT_OFFSET),) -$(info "WLAN: KERNEL_TO_BUILD_ROOT_OFFSET not defined, assuming default") -KERNEL_TO_BUILD_ROOT_OFFSET := ../ -endif - -LOCAL_PATH := $(call my-dir) - -# This makefile is only for DLKM -ifneq ($(findstring vendor,$(LOCAL_PATH)),) - -# Determine if we are Proprietary or Open Source -ifneq ($(findstring opensource,$(LOCAL_PATH)),) - WLAN_PROPRIETARY := 0 - WLAN_OPEN_SOURCE := 1 -else - WLAN_PROPRIETARY := 1 - WLAN_OPEN_SOURCE := 0 -endif - -ifeq ($(WLAN_PROPRIETARY),1) - WLAN_BLD_DIR := vendor/qcom/proprietary/wlan-noship -else - WLAN_BLD_DIR := vendor/qcom/opensource/wlan -endif - -# DLKM_DIR was moved for JELLY_BEAN (PLATFORM_SDK 16) -ifeq ($(call is-platform-sdk-version-at-least,16),true) - DLKM_DIR := $(TOP)/device/qcom/common/dlkm -else - DLKM_DIR := build/dlkm -endif - -# Copy WCNSS_cfg.dat and WCNSS_qcom_cfg.ini file from firmware_bin/ folder to target out directory. -ifeq ($(call is-board-platform-in-list, msm8960),true) -$(shell rm -f $(TARGET_OUT_ETC)/firmware/wlan/qca_cld/WCNSS_cfg.dat) -$(shell rm -f $(TARGET_OUT_ETC)/firmware/wlan/qca_cld/WCNSS_qcom_cfg.ini) -$(shell cp $(LOCAL_PATH)/firmware_bin/WCNSS_cfg.dat $(TARGET_OUT_ETC)/firmware/wlan/qca_cld) -$(shell cp $(LOCAL_PATH)/firmware_bin/WCNSS_qcom_cfg.ini $(TARGET_OUT_ETC)/firmware/wlan/qca_cld) -endif - -########################################################### -# This is set once per LOCAL_PATH, not per (kernel) module -KBUILD_OPTIONS := WLAN_ROOT=$(KERNEL_TO_BUILD_ROOT_OFFSET)$(WLAN_BLD_DIR)/qcacld-2.0 -# We are actually building wlan.ko here, as per the -# requirement we are specifying <chipset>_wlan.ko as LOCAL_MODULE. -# This means we need to rename the module to <chipset>_wlan.ko -# after wlan.ko is built. -KBUILD_OPTIONS += MODNAME=wlan -KBUILD_OPTIONS += BOARD_PLATFORM=$(TARGET_BOARD_PLATFORM) -KBUILD_OPTIONS += $(WLAN_SELECT) -KBUILD_OPTIONS += WLAN_OPEN_SOURCE=$(WLAN_OPEN_SOURCE) - -#module to be built for all user,userdebug and eng tags -include $(CLEAR_VARS) -LOCAL_MODULE := $(WLAN_CHIPSET)_wlan.ko -LOCAL_MODULE_KBUILD_NAME := wlan.ko -LOCAL_MODULE_TAGS := optional -LOCAL_MODULE_DEBUG_ENABLE := true -ifeq ($(PRODUCT_VENDOR_MOVE_ENABLED), true) -LOCAL_MODULE_PATH := $(TARGET_OUT_VENDOR)/lib/modules/$(WLAN_CHIPSET) -else -LOCAL_MODULE_PATH := $(TARGET_OUT)/lib/modules/$(WLAN_CHIPSET) -endif # PRODUCT_VENDOR_MOVE_ENABLED -include $(DLKM_DIR)/AndroidKernelModule.mk -########################################################### - -# Create Symbolic link for built <WLAN_CHIPSET>_wlan.ko driver from -# standard module location. -# TO-DO: This step needs to be moved to a post-build make target instead -# TO-DO: as this may run multiple times -ifneq ($(call is-board-platform-in-list, msm8952),true) -ifeq ($(PRODUCT_VENDOR_MOVE_ENABLED), true) -$(shell mkdir -p $(TARGET_OUT_VENDOR)/lib/modules; \ - ln -sf /$(TARGET_COPY_OUT_VENDOR)/lib/modules/$(WLAN_CHIPSET)/$(WLAN_CHIPSET)_wlan.ko \ - $(TARGET_OUT_VENDOR)/lib/modules/wlan.ko) -else -$(shell mkdir -p $(TARGET_OUT)/lib/modules; \ - ln -sf /system/lib/modules/$(WLAN_CHIPSET)/$(WLAN_CHIPSET)_wlan.ko \ - $(TARGET_OUT)/lib/modules/wlan.ko) -endif # PRODUCT_VENDOR_MOVE_ENABLED -endif -$(shell ln -sf /persist/wlan_mac.bin $(TARGET_OUT_ETC)/firmware/wlan/qca_cld/wlan_mac.bin) - -ifeq ($(call is-board-platform-in-list, msm8960),true) -$(shell ln -sf /firmware/image/bdwlan20.bin $(TARGET_OUT_ETC)/firmware/fakeboar.bin) -$(shell ln -sf /firmware/image/otp20.bin $(TARGET_OUT_ETC)/firmware/otp.bin) -$(shell ln -sf /firmware/image/utf20.bin $(TARGET_OUT_ETC)/firmware/utf.bin) -$(shell ln -sf /firmware/image/qwlan20.bin $(TARGET_OUT_ETC)/firmware/athwlan.bin) - -$(shell ln -sf /firmware/image/bdwlan20.bin $(TARGET_OUT_ETC)/firmware/bdwlan20.bin) -$(shell ln -sf /firmware/image/otp20.bin $(TARGET_OUT_ETC)/firmware/otp20.bin) -$(shell ln -sf /firmware/image/utf20.bin $(TARGET_OUT_ETC)/firmware/utf20.bin) -$(shell ln -sf /firmware/image/qwlan20.bin $(TARGET_OUT_ETC)/firmware/qwlan20.bin) - -$(shell ln -sf /firmware/image/bdwlan30.bin $(TARGET_OUT_ETC)/firmware/bdwlan30.bin) -$(shell ln -sf /firmware/image/otp30.bin $(TARGET_OUT_ETC)/firmware/otp30.bin) -$(shell ln -sf /firmware/image/utf30.bin $(TARGET_OUT_ETC)/firmware/utf30.bin) -$(shell ln -sf /firmware/image/qwlan30.bin $(TARGET_OUT_ETC)/firmware/qwlan30.bin) -endif - -# Copy config ini files to target -ifeq ($(call is-board-platform-in-list, msm8994),false) -ifeq ($(WLAN_PROPRIETARY),1) -$(shell mkdir -p $(TARGET_OUT)/etc/firmware/wlan/$(WLAN_CHIPSET)) -$(shell mkdir -p $(TARGET_OUT)/etc/wifi) -$(shell rm -f $(TARGET_OUT)/etc/wifi/WCNSS_qcom_cfg.ini) -$(shell rm -f $(TARGET_OUT)/etc/firmware/wlan/$(WLAN_SHIPSET)/WCNSS_cfg.dat) -$(shell cp $(LOCAL_PATH)/firmware_bin/WCNSS_qcom_cfg.ini $(TARGET_OUT)/etc/wifi) -$(shell cp $(LOCAL_PATH)/firmware_bin/WCNSS_cfg.dat $(TARGET_OUT)/etc/firmware/wlan/$(WLAN_CHIPSET)) -endif -endif - -endif # DLKM check -endif # Supported kernel check -endif # supported target check -endif # WLAN enabled check diff --git a/drivers/staging/qcacld-2.0/firmware_bin/WCNSS_cfg.dat b/drivers/staging/qcacld-2.0/firmware_bin/WCNSS_cfg.dat Binary files differdeleted file mode 100755 index 08aaf2bfd38b..000000000000 --- a/drivers/staging/qcacld-2.0/firmware_bin/WCNSS_cfg.dat +++ /dev/null diff --git a/drivers/staging/qcacld-2.0/firmware_bin/WCNSS_qcom_cfg.ini b/drivers/staging/qcacld-2.0/firmware_bin/WCNSS_qcom_cfg.ini deleted file mode 100755 index fa852a898d31..000000000000 --- a/drivers/staging/qcacld-2.0/firmware_bin/WCNSS_qcom_cfg.ini +++ /dev/null @@ -1,686 +0,0 @@ -# This file allows user to override the factory - -# defaults for the WLAN Driver - - -# Enable IMPS or not -gEnableImps=1 - -# Enable/Disable Idle Scan -gEnableIdleScan=0 - - -# Increase sleep duration (seconds) during IMPS -# 0 implies no periodic wake up from IMPS. Periodic wakeup is -# unnecessary if Idle Scan is disabled. -gImpsModSleepTime=0 - - -# Enable BMPS or not -gEnableBmps=1 - -# Enable suspend or not - -# 1: Enable standby, 2: Enable Deep sleep, 3: Enable Mcast/Bcast Filter - -gEnableSuspend=3 - -# Phy Mode (auto, b, g, n, etc) -# Valid values are 0-9, with 0 = Auto, 4 = 11n, 9 = 11ac -# 1 = 11abg, 2 = 11b, 3 = 11g, 5 = 11g only, 6 = 11n only -# 7 = 11b only 8 = 11ac only. -gDot11Mode=0 - - -# CSR Roaming Enable(1) Disable(0) - -gRoamingTime=0 - - -# Assigned MAC Addresses - This will be used until NV items are in place - -# Each byte of MAC address is represented in Hex format as XX - -Intf0MacAddress=000AF58989FF -Intf1MacAddress=000AF58989FE -Intf2MacAddress=000AF58989FD - -Intf3MacAddress=000AF58989FC - - -# UAPSD service interval for VO,VI, BE, BK traffic - -InfraUapsdVoSrvIntv=0 - -InfraUapsdViSrvIntv=0 - -InfraUapsdBeSrvIntv=0 - -InfraUapsdBkSrvIntv=0 - -# Flag to allow STA send AddTspec even when ACM is Off -gAddTSWhenACMIsOff=1 - -# Make 1x1 the default antenna configuration - -gNumRxAnt=1 - - -# Beacon filtering frequency (unit in beacon intervals) - -gNthBeaconFilter=50 - - -# Enable WAPI or not - -# WAPIIsEnabled=0 - - -# Flags to filter Mcast abd Bcast RX packets. - -# Value 0: No filtering, 1: Filter all Multicast. - -# 2: Filter all Broadcast. 3: Filter all Mcast abd Bcast - -McastBcastFilter=3 - - -#Flag to enable HostARPOffload feature or not - -hostArpOffload=1 - -#Flag to enable TCPChkSumOffld feature or not - -gEnableTCPChkSumOffld=1 - -#Flag to enable HostNSOffload feature or not - -hostNSOffload=1 - -#Flag to enable IPChkSumOffld feature or not - -gEnableIPChecksumOffload=1 - -#SoftAP Related Parameters - -# AP MAc addr - -gAPMacAddr=000AF589dcab - - -# 802.11n Protection flag - -gEnableApProt=1 - - -#Enable OBSS protection - -gEnableApOBSSProt=1 - - -#Enable/Disable UAPSD for SoftAP - -gEnableApUapsd=1 - - -# Fixed Rate - -gFixedRate=0 - - -# Maximum Tx power - -# gTxPowerCap=30 - - -# Fragmentation Threshold - -# gFragmentationThreshold=2346 - - -# RTS threshold - -RTSThreshold=1048576 - - -# Intra-BSS forward - -gDisableIntraBssFwd=0 - - -# WMM Enable/Disable - -WmmIsEnabled=0 - - -# 802.11d support - -g11dSupportEnabled=0 - -# 802.11h support - -g11hSupportEnabled=1 - -# DFS Master Capability -gEnableDFSMasterCap=1 - -# ESE Support and fast transition -EseEnabled=1 -ImplicitQosIsEnabled=0 -gNeighborScanTimerPeriod=200 - -gNeighborLookupThreshold=76 -gNeighborReassocThreshold=81 - -gNeighborScanChannelMinTime=20 -gNeighborScanChannelMaxTime=30 -gMaxNeighborReqTries=3 - -# Legacy (non-ESE, non-802.11r) Fast Roaming Support -# To enable, set FastRoamEnabled=1 -# To disable, set FastRoamEnabled=0 -FastRoamEnabled=1 - -#Check if the AP to which we are roaming is better than current AP in terms of RSSI. -#Checking is disabled if set to Zero.Otherwise it will use this value as to how better -#the RSSI of the new/roamable AP should be for roaming -RoamRssiDiff=3 - -# If the RSSI of any available candidate is better than currently associated -# AP by at least gImmediateRoamRssiDiff, then being to roam immediately (without -# registering for reassoc threshold). -# NOTE: Value of 0 means that we would register for reassoc threshold. -gImmediateRoamRssiDiff=10 - -# To enable, set gRoamIntraBand=1 (Roaming within band) -# To disable, set gRoamIntraBand=0 (Roaming across band) -gRoamIntraBand=0 - -# SAP Country code - -# Default Country Code is 2 bytes, 3rd byte is optional indoor or out door. - -# Example - -# US Indoor, USI - -# Korea Outdoor, KRO - -# Japan without optional byte, JP - -# France without optional byte, FR - -#gAPCntryCode=USI - - -#Short Guard Interval Enable/disable - -gShortGI20Mhz=1 - -gShortGI40Mhz=1 - - -#Auto Shutdown Value in seconds. A value of 0 means Auto shutoff is disabled - -gAPAutoShutOff=0 - -#Auto Shutdown wlan : Value in Seconds. 0 means disabled. Max 1 day = 86400 sec -gWlanAutoShutdown = 0 - - -# Listen Energy Detect Mode Configuration - -# Valid values 0-128 - -# 128 means disable Energy Detect feature - -# 0-9 are threshold code and 7 is recommended value from system if feature is to be enabled. - -# 10-128 are reserved. - -# The EDET threshold mapping is as follows in 3dB step: - -# 0 = -60 dBm - -# 1 = -63 dBm - -# 2 = -66 dBm - -# ... - -# 7 = -81 dBm - -# 8 = -84 dBm - -# 9 = -87 dBm - -# Note: Any of these settings are valid. Setting 0 would yield the highest power saving (in a noisy environment) at the cost of more range. The range impact is approximately #calculated as: - -# - -# Range Loss (dB) = EDET threshold level (dBm) + 97 dBm. - -# - -gEnablePhyAgcListenMode=128 - - -#Preferred band (both or 2.4 only or 5 only) - -BandCapability=0 - - -#Beacon Early Termination (1 = enable the BET feature, 0 = disable) - -enableBeaconEarlyTermination=0 - -beaconEarlyTerminationWakeInterval=3 - - -#Channel Bonding -gChannelBondingMode5GHz=1 - - -#Enable Keep alive with non-zero period value - -gStaKeepAlivePeriod = 30 - -#Say gGoKeepAlivePeriod(5 seconds) and gGoLinkMonitorPeriod(10 seconds). -#For every 10 seconds DUT send Qos Null frame(i.e., Keep Alive frame if link is idle for last 10 seconds.) -#For both active and power save clients. - -#Power save clients: DUT set TIM bit from 10th second onwards and till client honors TIM bit. -#If doesn't honor for 5 seconds then DUT remove client. - -#Active clients: DUT send Qos Null frame for 10th seconds onwards if it is not success still we try on -#11th second if not tries on 12th and so on till 15th second. Hence before disconnection DUT will send 5 NULL frames. -#Hence in any case DUT will detect client got removed in (10+5) seconds. i.e., (gGoKeepAlivePeriod + gGoLinkMonitorPeriod).. - -#gGoLinkMonitorPeriod/ gApLinkMonitorPeriod is period where link is idle and it is period -#where we send NULL frame. - -gApLinkMonitorPeriod = 30 - -gGoLinkMonitorPeriod = 10 - -#gGoKeepAlivePeriod/gApKeepAlivePeriod is time to spend to check whether frame are succeed to send or not. -#Hence total effective detection time is gGoLinkMonitorPeriod+ gGoKeepAlivePeriod/gApLinkMonitorPeriod+ gApKeepAlivePeriod. - - -gGoKeepAlivePeriod = 3 - -gApKeepAlivePeriod = 10 - - -#If set will start with active scan after driver load, otherwise will start with - -#passive scan to find out the domain - -gEnableBypass11d=1 - - -#If set to 0, will not scan DFS channels - -gEnableDFSChnlScan=1 - -# Enable DFS channel roam -# 0: DISABLE, 1: ENABLED_NORMAL, 2: ENABLED_ACTIVE -gAllowDFSChannelRoam=1 - -gVhtChannelWidth=2 - - -# Enable Automatic Tx Power control - -gEnableAutomaticTxPowerControl=1 - -# 0 for OLPC 1 for CLPC and SCPC -gEnableCloseLoop=1 - -#Data Inactivity Timeout when in powersave (in ms) -gDataInactivityTimeout=200 - -# VHT Tx/Rx MCS values -# Valid values are 0,1,2. If commented out, the default value is 0. -# 0=MCS0-7, 1=MCS0-8, 2=MCS0-9 -gVhtRxMCS=2 -gVhtTxMCS=2 - -# VHT Tx/Rx MCS values for 2x2 -# Valid values are 0,1,2. If commented out, the default value is 0. -# 0=MCS0-7, 1=MCS0-8, 2=MCS0-9 -gVhtRxMCS2x2=2 -gVhtTxMCS2x2=2 - - -# Valid chain mask values -# 01 - enables chain0 -# 02 - enables chain1 -# 03 - enables both chain 0 and chain 1 -# if set to 0 or 1 then all vdevs comes up in 1x1 mode in that band. -gChainMask_2g=3 -gChainMask_5g=3 - -# NSS cfg bit definition. -# STA BIT[0:1] -# SAP BIT[2:3] -# P2P_GO BIT[4:5] -# P2P_CLIENT BIT[6:7] -# IBSS BIT[8:9] -# TDLS BIT[10:11] -# P2P_DEVICE BIT[12:13] -# OCB BIT[14:15] -# Valid values are 1 or 2 for each two bit configuration. -# if 2-bit value is set to 1 then the corresponidng vdev comes up in 1x1 mode -# in the band, if set to 2 then that vdev comes up in 2x2 mode in that band. -gVdevTypeNss_2g=43690 -gVdevTypeNss_5g=43690 - -gTxChainMask1ss=0 - -# Scan Timing Parameters -# gPassiveMaxChannelTime=110 -# gPassiveMinChannelTime=60 -gActiveMaxChannelTime=80 -gActiveMinChannelTime=40 - -#If set to 0, MCC is not allowed. -gEnableMCCMode=1 - -# MCC to SCC Switch mode: 0-Disable 1-Enable 2-Force SCC if same band -gWlanMccToSccSwitchMode = 0 - -# Band Switch Enable/Disable for MCC to SCC -gWlanBandSwitchEnable = 0 - -# 1=enable STBC; 0=disable STBC -gEnableRXSTBC=1 - -# 1=enable tx STBC; 0=disable -gEnableTXSTBC=1 - -# 1=enable rx LDPC; 0=disable -gEnableRXLDPC=1 - -# Enable Tx beamforming in VHT20MHz -# Valid values are 0,1. If commented out, the default value is 0. -# 0=disable, 1=enable -gEnableTxBFin20MHz=1 - -# Enable Active mode offload -gEnableActiveModeOffload=1 - -#Enable Scan Results Aging based on timer -#Timer value is in seconds -#If Set to 0 it will not enable the feature -gScanAgingTime=0 - -#Enable Scan Results Aging based on number of scans -gScanResultAgeCount=1 - -#Enable Power saving mechanism Based on Android Framework -#If set to 0 Driver internally control the Power saving mechanism -#If set to 1 Android Framwrok control the Power saving mechanism -isAndroidPsEn=0 - -#Enable thermal mitigation -gThermalMitigationEnable=0 - -gEnableFastRoamInConcurrency=1 - -#List of Country codes for which 11ac needs to be disabled -#Each country code must be delimited by comma(,) -gListOfNon11acCountryCode=RU,UA,ZA - -#Maxium Channel time in msec -gMaxMediumTime = 6000 - -# 802.11K support -gRrmEnable=1 -gRrmOperChanMax=8 -gRrmNonOperChanMax=8 -gRrmRandIntvl=100 - -#Scan offload -gEnableDirectedScanOffload=1 - -#FlexConnect Power Factor -#Default is set to 0 (disable) -gFlexConnectPowerFactor=0 - -#Disable split scan, the FW will take care of it -gNumChanCombinedConc=60 - -#Enable Power Save offload -gEnablePowerSaveOffload=2 - -#Enable firmware uart print -gEnablefwprint=0 - -#Enable firmware log -gEnablefwlog=1 -# Additional firmware log levels -gFwDebugLogLevel=4 -gFwDebugModuleLoglevel=1,0,2,0,4,0,5,0,6,0,7,4,8,0,9,0,11,0,13,0,17,0,18,0,19,0,27,0,29,0,31,0,35,0,36,0,38,0 - -#IPA config -gIPAConfig=0 -gIPADescSize=800 -gIPAPreFilterEnable=1 -gIPARMEnable=1 -gIPAIPv6Enable=1 - -#P2P Listen offload -gEnableP2pListenOffload=1 - -# Maximum MPDU length (VHT only. Valid values: 0->3895 octets, 1->7991 octets, 2->11454 octets) -gVhtMpduLen=2 - -# Maximum number of wow filters required -#gMaxWoWFilters=22 - -# WOW Enable/Disable. -# 0 - Disable both magic pattern match and pattern byte match. -# 1 - Enable magic pattern match on all interfaces. -# 2 - Enable pattern byte match on all interfaces. -# 3 - Enable both magic patter and pattern byte match on all interfaces. -# Default value of gEnableWoW is 3. -# gEnableWoW=0 - -# Enable or Disable MCC Adaptive Scheduler at the FW -# 1=Enable (default), 0=Disable -gEnableMCCAdaptiveScheduler=1 - -#Enable or Disable p2p device address administered -isP2pDeviceAddrAdministrated=1 - -# RX packet handling options -# 0: no rx thread, no RPS, for MDM -# 1: RX thread -# 2: RPS -rxhandle=2 - -# Set RPS CPU MAP as 0xe for the 4 RX queues -# This allows use of CPU1-CPU3 but not CPU0 for 4 RX queues -rpsRxQueueCpuMapList=c - -# Remove Overlap channel restriction -gEnableOverLapCh=0 - -#Enable VHT on 2.4Ghz -gEnableVhtFor24GHzBand=1 - -#Enable or Disable 5G early beacon termination -gEnable5gEBT=1 - -#Maximum number of offload peers supported -# gMaxOffloadPeers=2 - -# controlling the following offload patterns -# through ini parameter. Default value is 1 -# to disable set it to zero. ssdp = 0 -# Setup multicast pattern for mDNS 224.0.0.251, -# SSDP 239.255.255.250 and LLMNR 224.0.0.252 - - -ssdp = 0 - -#Enable Memory Deep Sleep -gEnableMemDeepSleep=1 - -# Bus bandwidth threshold values in terms of number of packets -gBusBandwidthHighThreshold=2000 -gBusBandwidthMediumThreshold=500 -gBusBandwidthLowThreshold=150 - -# IPA bandwidth voting -gIPAHighBandwidthMbps=800 -gIPAMediumBandwidthMbps=400 -gIPALowBandwidthMbps=200 - -# Bus bandwidth compute timeout value in ms -gBusBandwidthComputeInterval=100 - -# Regulatory Setting; 0=STRICT; 1=CUSTOM -gRegulatoryChangeCountry=1 -# RA filtering rate limit param, the current value would not -# help if the lifetime in RA is less than 3*60=3min. Then -# we need to change it, though it is uncommon. -# gRAFilterEnable=0 -gRArateLimitInterval=600 - -# Maximum number of concurrent connections -gMaxConcurrentActiveSessions=2 - -# Disable/Enable GreenAP -# 0 to disable, 1 to enable, default: 1 -gEnableGreenAp=1 - -# Radar PRI multiplier -gDFSradarMappingPriMultiplier=4 - -gPNOScanSupport=0 - -# Enable/Disable RX full reorder offload -gReorderOffloadSupported=1 - -# Enable/Disable LPASS support -# 0 to disable, 1 to enable -gEnableLpassSupport=1 - -# Whether userspace country code setting shld have priority -gCountryCodePriority=1 - -# Enable(1)/Disable(0) SIFS burst -gEnableSifsBurst=1 - -# Enable/Disable channel avoidance for SAP in SCC scenario -# 0 - disable -# 1 - enable -gSapSccChanAvoidance=0 - -# Inactivity time (in ms) to end TX Service Period while in IBSS power save mode -gIbssTxSpEndInactivityTime=10 - -# Enable/Disable Roaming Offload Support (a.k.a Key Management Offload) -# 0 to disable, 1 to enable -gRoamOffloadEnabled=0 - -# Enable support for TDLS -# 0 - disable -# 1 - enable -gEnableTDLSSupport=1 - -# Enable support for Implicit Trigger of TDLS. That is, wlan driver shall -# initiate TDLS Discovery towards a peer whenever setup criteria (throughput -# and RSSI) is met and then will initiate teardown when teardown criteria -# (idle packet count and RSSI) is met. -# 0 - disable -# 1 - enable -gEnableTDLSImplicitTrigger=1 - -# Enable TDLS External Control. That is, user space application has to -# first configure a peer MAC in wlan driver towards which TDLS is desired. -# Device will establish TDLS only towards those configured peers whenever -# TDLS criteria (throughput and RSSI threshold) is met and teardown TDLS -# when teardown criteria (idle packet count and RSSI) is met. However, -# device will accept TDLS connection if it is initiated from any other peer, -# even if that peer is not configured. -# 0 - disable -# 1 - enable -# For TDLS External Control, Implicit Trigger must also be enabled. -gTDLSExternalControl=1 - -# Enable support for TDLS off-channel operation -# 0 - disable -# 1 - enable -# TDLS off-channel operation will be invoked when there is only one -# TDLS connection. -gEnableTDLSOffChannel=1 - -IpaUcOffloadEnabled=1 -gIpaUcStaOffload=1 - -gEnableSelfRecovery=1 - -# Enable or Disable Random MAC (Spoofing) -# 1=Enable, 0=Disable (default) -gEnableMacAddrSpoof=0 - -# Enable Auto suspend feature -# When this feature is enabled, it will shutdown the PCIe link -# when inactivity is detected in STA disconnected mode. -# 0 - disable -# 1 - enable -gEnableBusAutoSuspend=0 - -# Enable Runtime PM Feature. -# Enabling this feature will put target wow and shutdown pcie link -# when inactivity is detected in WLAN Driver. -# This feature is inactive when beaconing interfaces are active with -# clients associated. -# 0 - disable -# 1 - enable - -gRuntimePM=1 -# When gRuntimePM is disabled gRuntimeAutoTime won't take effect. -# The Time is in msec. -# 100 is min, 10000 is max, 500 is default. - -gRuntimePMDelay=500 - -# Enable to check FW hash if secure FW feature is enabled. It's for defconfig -# builds only since it will be ignored in performance/release builds. -gEnableFWHashCheck=1 - -# Enable FW to filter out broadcast packets and wakeup host during runtime PM. -# As APPS is awake during runtime PM, if any application needs the broadcast -# packets OEM's can enable this flag. -# FW will filters the broadcast packets and wakeup host to deliver them during -# runtime suspend. -# This flag will take affect when Runtime PM is enabled -gRuntimePmEnableBcastPattern=0 - -# intervals length (in ms) during WLAN P2P (single vdev) + BT Paging -# min 20ms, max 200ms -gBTIntervalPageP2P=30 -gWLIntervalPageP2P=30 - -# intervals length (in ms) during WLAN STA (single vdev) + BT Paging -# min 20ms, max 200ms -gBTIntervalPageSTA=30 -gWLIntervalPageSTA=30 - -# intervals length (in ms) during WLAN SAP (single vdev) + BT Paging -# min 20ms, max 200ms -gBTIntervalPageSAP=30 -gWLIntervalPageSAP=30 - -# Enable OCB/DSRC tx per packet stats, disable it as default because -# it would degrade throughput -gOcbTxPerPktStatsEnable=0 - -END - -# Note: Configuration parser would not read anything past the END marker - diff --git a/drivers/staging/qcacld-2.0/firmware_bin/WCNSS_qcom_cfg.usb.ini b/drivers/staging/qcacld-2.0/firmware_bin/WCNSS_qcom_cfg.usb.ini deleted file mode 100644 index e830762a8bf0..000000000000 --- a/drivers/staging/qcacld-2.0/firmware_bin/WCNSS_qcom_cfg.usb.ini +++ /dev/null @@ -1,567 +0,0 @@ -# This file allows user to override the factory - -# defaults for the WLAN Driver - - -# Enable IMPS or not -gEnableImps=1 - -# Enable/Disable Idle Scan - -gEnableIdleScan=0 - - -# Increase sleep duration (seconds) during IMPS -# 0 implies no periodic wake up from IMPS. Periodic wakeup is -# unnecessary if Idle Scan is disabled. -gImpsModSleepTime=0 - - -# Enable BMPS or not -gEnableBmps=1 - -# Enable suspend or not - -# 1: Enable standby, 2: Enable Deep sleep, 3: Enable Mcast/Bcast Filter - -gEnableSuspend=3 - - -# Phy Mode (auto, b, g, n, etc) -# Valid values are 0-9, with 0 = Auto, 4 = 11n, 9 = 11ac -# 1 = 11abg, 2 = 11b, 3 = 11g, 5 = 11g only, 6 = 11n only -# 7 = 11b only 8 = 11ac only. -gDot11Mode=0 - - -# CSR Roaming Enable(1) Disable(0) - -gRoamingTime=0 - - -# Assigned MAC Addresses - This will be used until NV items are in place - -# Each byte of MAC address is represented in Hex format as XX - -Intf0MacAddress=000AF58989FF -Intf1MacAddress=000AF58989FE -Intf2MacAddress=000AF58989FD - -Intf3MacAddress=000AF58989FC - - -# UAPSD service interval for VO,VI, BE, BK traffic - -InfraUapsdVoSrvIntv=0 - -InfraUapsdViSrvIntv=0 - -InfraUapsdBeSrvIntv=0 - -InfraUapsdBkSrvIntv=0 - -# Flag to allow STA send AddTspec even when ACM is Off -gAddTSWhenACMIsOff=1 - -# Make 1x1 the default antenna configuration - -gNumRxAnt=1 - - -# Beacon filtering frequency (unit in beacon intervals) - -gNthBeaconFilter=50 - - -# Enable WAPI or not - -# WAPIIsEnabled=0 - - -# Flags to filter Mcast abd Bcast RX packets. - -# Value 0: No filtering, 1: Filter all Multicast. - -# 2: Filter all Broadcast. 3: Filter all Mcast abd Bcast - -McastBcastFilter=3 - - -#Flag to enable HostARPOffload feature or not - -hostArpOffload=1 - -#Flag to enable TCPChkSumOffld feature or not - -gEnableTCPChkSumOffld=1 - -#Flag to enable HostNSOffload feature or not - -hostNSOffload=1 - -#Flag to enable IPChkSumOffld feature or not - -gEnableIPChecksumOffload=0 - -#SoftAP Related Parameters - -# AP MAc addr - -gAPMacAddr=000AF589dcab - - -# 802.11n Protection flag - -gEnableApProt=1 - - -#Enable OBSS protection - -gEnableApOBSSProt=1 - - -#Enable/Disable UAPSD for SoftAP - -gEnableApUapsd=1 - - -# Fixed Rate - -gFixedRate=0 - - -# Maximum Tx power - -# gTxPowerCap=30 - - -# Fragmentation Threshold - -# gFragmentationThreshold=2346 - - -# RTS threshold - -RTSThreshold=192000 - - -# Intra-BSS forward - -gDisableIntraBssFwd=0 - - -# WMM Enable/Disable - -WmmIsEnabled=0 - - -# 802.11d support - -g11dSupportEnabled=1 - -# 802.11h support - -g11hSupportEnabled=1 - -# ESE Support and fast transition -EseEnabled=0 -ImplicitQosIsEnabled=0 -gNeighborScanTimerPeriod=200 - -gNeighborLookupThreshold=76 -gNeighborReassocThreshold=81 - -gNeighborScanChannelMinTime=20 -gNeighborScanChannelMaxTime=30 -gMaxNeighborReqTries=3 - -# Legacy (non-ESE, non-802.11r) Fast Roaming Support -# To enable, set FastRoamEnabled=1 -# To disable, set FastRoamEnabled=0 -FastRoamEnabled=1 - -#Check if the AP to which we are roaming is better than current AP in terms of RSSI. -#Checking is disabled if set to Zero.Otherwise it will use this value as to how better -#the RSSI of the new/roamable AP should be for roaming -RoamRssiDiff=3 - -# If the RSSI of any available candidate is better than currently associated -# AP by at least gImmediateRoamRssiDiff, then being to roam immediately (without -# registering for reassoc threshold). -# NOTE: Value of 0 means that we would register for reassoc threshold. -gImmediateRoamRssiDiff=10 - -# To enable, set gRoamIntraBand=1 (Roaming within band) -# To disable, set gRoamIntraBand=0 (Roaming across band) -gRoamIntraBand=0 - -# SAP Country code - -# Default Country Code is 2 bytes, 3rd byte is optional indoor or out door. - -# Example - -# US Indoor, USI - -# Korea Outdoor, KRO - -# Japan without optional byte, JP - -# France without optional byte, FR - -#gAPCntryCode=USI - - -#Short Guard Interval Enable/disable - -gShortGI20Mhz=1 - -gShortGI40Mhz=1 - - -#Auto Shutdown Value in seconds. A value of 0 means Auto shutoff is disabled - -gAPAutoShutOff=0 - - -# SAP auto channel selection configuration - -# 0 = disable auto channel selection - -# 1 = enable auto channel selection, channel provided by supplicant will be ignored - -gApAutoChannelSelection=0 - - -# Listen Energy Detect Mode Configuration - -# Valid values 0-128 - -# 128 means disable Energy Detect feature - -# 0-9 are threshold code and 7 is recommended value from system if feature is to be enabled. - -# 10-128 are reserved. - -# The EDET threshold mapping is as follows in 3dB step: - -# 0 = -60 dBm - -# 1 = -63 dBm - -# 2 = -66 dBm - -# ... - -# 7 = -81 dBm - -# 8 = -84 dBm - -# 9 = -87 dBm - -# Note: Any of these settings are valid. Setting 0 would yield the highest power saving (in a noisy environment) at the cost of more range. The range impact is approximately #calculated as: - -# - -# Range Loss (dB) = EDET threshold level (dBm) + 97 dBm. - -# - -gEnablePhyAgcListenMode=128 - - -#Preferred band (both or 2.4 only or 5 only) - -BandCapability=0 - - -#Beacon Early Termination (1 = enable the BET feature, 0 = disable) - -enableBeaconEarlyTermination=0 - -beaconEarlyTerminationWakeInterval=3 - - -#SOFTAP Channel Range selection - -gAPChannelSelectStartChannel=1 - -gAPChannelSelectEndChannel=11 - - -#SOFTAP Channel Range selection Operating band - -# 0:2.4GHZ 1: LOW-5GHZ 2:MID-5GHZ 3:HIGH-5GHZ 4: 4.9HZ BAND - -gAPChannelSelectOperatingBand=0 - - -#Channel Bonding -gChannelBondingMode5GHz=1 - - -#Enable Keep alive with non-zero period value - -gStaKeepAlivePeriod = 30 - -#Say gGoKeepAlivePeriod(5 seconds) and gGoLinkMonitorPeriod(10 seconds). -#For every 10 seconds DUT send Qos Null frame(i.e., Keep Alive frame if link is idle for last 10 seconds.) -#For both active and power save clients. - -#Power save clients: DUT set TIM bit from 10th second onwards and till client honors TIM bit. -#If doesn't honor for 5 seconds then DUT remove client. - -#Active clients: DUT send Qos Null frame for 10th seconds onwards if it is not success still we try on -#11th second if not tries on 12th and so on till 15th second. Hence before disconnection DUT will send 5 NULL frames. -#Hence in any case DUT will detect client got removed in (10+5) seconds. i.e., (gGoKeepAlivePeriod + gGoLinkMonitorPeriod).. - -#gGoLinkMonitorPeriod/ gApLinkMonitorPeriod is period where link is idle and it is period -#where we send NULL frame. - -#gApLinkMonitorPeriod = 10 - -#gGoLinkMonitorPeriod = 10 - -#gGoKeepAlivePeriod/gApKeepAlivePeriod is time to spend to check whether frame are succeed to send or not. -#Hence total effective detection time is gGoLinkMonitorPeriod+ gGoKeepAlivePeriod/gApLinkMonitorPeriod+ gApKeepAlivePeriod. - - -gGoKeepAlivePeriod = 20 - -gApKeepAlivePeriod = 20 - - -#If set will start with active scan after driver load, otherwise will start with - -#passive scan to find out the domain - -gEnableBypass11d=1 - - -#If set to 0, will not scan DFS channels - -gEnableDFSChnlScan=1 - - -gVhtChannelWidth=2 -gEnableLogp=1 - - -# Enable Automatic Tx Power control - -gEnableAutomaticTxPowerControl=1 - -# 0 for OLPC 1 for CLPC and SCPC -gEnableCloseLoop=1 - -#Data Inactivity Timeout when in powersave (in ms) -gDataInactivityTimeout=200 - -# VHT Tx/Rx MCS values -# Valid values are 0,1,2. If commented out, the default value is 0. -# 0=MCS0-7, 1=MCS0-8, 2=MCS0-9 -gVhtRxMCS=2 -gVhtTxMCS=2 - -# VHT Tx/Rx MCS values for 2x2 -# Valid values are 0,1,2. If commented out, the default value is 0. -# 0=MCS0-7, 1=MCS0-8, 2=MCS0-9 -gEnable2x2=1 -gVhtRxMCS2x2=0 -gVhtTxMCS2x2=2 - -# Scan Timing Parameters -# gPassiveMaxChannelTime=110 -# gPassiveMinChannelTime=60 -# gActiveMaxChannelTime=40 -# gActiveMinChannelTime=20 - -#If set to 0, MCC is not allowed. -gEnableMCCMode=1 - -# 1=enable STBC; 0=disable STBC -gEnableRXSTBC=1 - -# 1=enable tx STBC; 0=disable -gEnableTXSTBC=1 - -# 1=enable rx LDPC; 0=disable -gEnableRXLDPC=1 - -# Enable Active mode offload -gEnableActiveModeOffload=1 - -#Enable Scan Results Aging based on timer -#Timer value is in seconds -#If Set to 0 it will not enable the feature -gScanAgingTime=0 - -#Enable Power saving mechanism Based on Android Framework -#If set to 0 Driver internally control the Power saving mechanism -#If set to 1 Android Framwrok control the Power saving mechanism -isAndroidPsEn=0 - -#disable LDPC in STA mode if the AP is TXBF capable -gDisableLDPCWithTxbfAP=1 - -#Enable thermal mitigation -gThermalMitigationEnable=1 -gThermalTempMinLevel1=90 -gThermalTempMaxLevel0=110 -gThermalTempMaxLevel1=115 -gThrottlePeriod=100 - -gEnableFastRoamInConcurrency=1 - -#List of Country codes for which 11ac needs to be disabled -#Each country code must be delimited by comma(,) -gListOfNon11acCountryCode=RU,UA,ZA - -#Maxium Channel time in msec -gMaxMediumTime = 6000 - -# 802.11K support -gRrmEnable=1 -gRrmOperChanMax=8 -gRrmNonOperChanMax=8 -gRrmRandIntvl=100 - -#Scan offload -gEnableDirectedScanOffload=1 - -#FlexConnect Power Factor -#Default is set to 0 (disable) -gFlexConnectPowerFactor=0 - -#Disable split scan, the FW will take care of it -gNumChanCombinedConc=60 - -#Enable Power Save offload -gEnablePowerSaveOffload=1 - -#Enable firmware uart print -gEnablefwprint=0 - -#Enable firmware log -gEnablefwlog=1 - -#IPA config -gIPAEnable=1 -gIPADescSize=800 -gIPAPreFilterEnable=1 -gIPARMEnable=1 - -#P2P Listen offload -gEnableP2pListenOffload=1 - -# Maximum Receive AMPDU size (VHT only. Valid values: 0->8k 1->16k 2->32k 3->64k 4->128k) -gVhtAmpduLenExponent=7 - -# Maximum MPDU length (VHT only. Valid values: 0->3895 octets, 1->7991 octets, 2->11454 octets) -gVhtMpduLen=0 - -# Maximum number of wow filters required -#gMaxWoWFilters=22 - -# WOW Enable/Disable. -# 0 - Disable both magic pattern match and pattern byte match. -# 1 - Enable magic pattern match on all interfaces. -# 2 - Enable pattern byte match on all interfaces. -# 3 - Enable both magic patter and pattern byte match on all interfaces. -# Default value of gEnableWoW is 3. -# gEnableWoW=0 - -# Enable or Disable MCC Adaptive Scheduler at the FW -# 1=Enable (default), 0=Disable -gEnableMCCAdaptiveScheduler=1 - -#Enable or Disable p2p device address administered -isP2pDeviceAddrAdministrated=0 - -#Disable scan_pno by default -gPNOScanSupport=0 - -#Enable TDLS -gEnableTDLSSupport=1 - -# Regulatory Setting; 0=STRICT; 1=CUSTOM -gRegulatoryChangeCountry=1 - -# Disable FW log function by default -gFwDebugLogType=0 -gFwDebugModuleLoglevel=0,0 - -# Enable or Disable Rx thread -# 1=Enable (default), 0=Disable -gEnableRxThread=0 - -# Enable or Disable FW self-recovery -# Currently, It's for USB only. -# 1=Enable, 0=Disable (default) -gEnableFwSelfRecovery=0 - -# Enable or Disable SAP suspend -# 1=Enable (default), 0=Disable -gEnableSapSuspend=0 - -# Enable TxBF -gTxBFEnable=1 - -# Enable or Disable DHCP Server offload -# 1=Enable, 0=Disable (default) -gDHCPServerOffloadEnable=0 -# Set max number of DHCP Clients -# Its value could not be greater than 10 -#gDHCPMaxNumClients=10 -# Set DHCP server IP -# 4th field could not be greater than 99, that is xxx,xxx,xxx,0 ~ xxx,xxx,xxx,99 -# 1st field could not be within the range of 224 ~ 239 (multicast IP address) -#gDHCPServerIP=192,168,1,2 - -# gEnableSAPAuthOffload: Enable Software AP Authentication Offload feature -# 1=Enable, 0=Disable (default) -gEnableSAPAuthOffload=0 -# gSAPAuthOffloadSec: Software AP Authentication Offload security Type, 0: disabled, 1: WPA2-PSK CCMP -# gSAPAuthOffloadSec=1 -# gSAPAuthOffloadKey: Passphrase of Security -# gSAPAuthOffloadKey=12345678 - - -# Enable or Disable UDP response offload feature -# 1=Enable, 0=Disable (default) -gudp_resp_offload_support=0 -# Set UDP packet dest port -# It's value is between 0 and 65535 -# Default is 0 -# gudp_resp_offload_dest_port=0 -# Set UDP payload filter -# It is only include Arabic numerals and English letter -# It's length should be between 1 and 127 -# gudp_resp_offload_payload_filter=require status -# Set UDP response payload -# It is only include Arabic numerals and English letter -# It's length should be between 1 and 127 -# gudp_resp_offload_response_payload=status=off - - - - -# Enable or Disable WOW Pulse feature -# 1 = Enable, 0 = Disable (default) -gwow_pulse_support = 0 -# GPIO PIN -# It's value is between 0 and 255 -# Default is 35 -# gwow_pulse_pin = 35 -# Set WOW Pulse interval low -# It's value is between 160 and 480 -# gwow_pulse_interval_low = 180 -# Set WOW Pulse interval high -# It's value is between 20 and 40 -# gwow_pulse_interval_high = 20 - - -END - -# Note: Configuration parser would not read anything past the END marker - |