Merge branch 'linux-linaro-lsk-v4.4' into linux-linaro-lsk-v4.4-android

4 files changed, 40 insertions, 16 deletions

diff --git a/drivers/tty/serial/8250/8250_mid.c b/drivers/tty/serial/8250/8250_mid.c
index 88531a36b69c..ed489880e62b 100644
--- a/drivers/tty/serial/8250/8250_mid.c
+++ b/drivers/tty/serial/8250/8250_mid.c
@@ -14,6 +14,7 @@
 #include <linux/pci.h>
 
 #include <linux/dma/hsu.h>
+#include <linux/8250_pci.h>
 
 #include "8250.h"
 
@@ -24,6 +25,7 @@
 #define PCI_DEVICE_ID_INTEL_DNV_UART	0x19d8
 
 /* Intel MID Specific registers */
+#define INTEL_MID_UART_DNV_FISR		0x08
 #define INTEL_MID_UART_PS		0x30
 #define INTEL_MID_UART_MUL		0x34
 #define INTEL_MID_UART_DIV		0x38
@@ -31,6 +33,7 @@
 struct mid8250;
 
 struct mid8250_board {
+	unsigned int flags;
 	unsigned long freq;
 	unsigned int base_baud;
 	int (*setup)(struct mid8250 *, struct uart_port *p);
@@ -88,16 +91,16 @@ static int tng_setup(struct mid8250 *mid, struct uart_port *p)
 static int dnv_handle_irq(struct uart_port *p)
 {
 	struct mid8250 *mid = p->private_data;
-	int ret;
-
-	ret = hsu_dma_irq(&mid->dma_chip, 0);
-	ret |= hsu_dma_irq(&mid->dma_chip, 1);
-
-	/* For now, letting the HW generate separate interrupt for the UART */
-	if (ret)
-		return ret;
-
-	return serial8250_handle_irq(p, serial_port_in(p, UART_IIR));
+	unsigned int fisr = serial_port_in(p, INTEL_MID_UART_DNV_FISR);
+	int ret = IRQ_NONE;
+
+	if (fisr & BIT(2))
+		ret |= hsu_dma_irq(&mid->dma_chip, 1);
+	if (fisr & BIT(1))
+		ret |= hsu_dma_irq(&mid->dma_chip, 0);
+	if (fisr & BIT(0))
+		ret |= serial8250_handle_irq(p, serial_port_in(p, UART_IIR));
+	return ret;
 }
 
 #define DNV_DMA_CHAN_OFFSET 0x80
@@ -106,12 +109,13 @@ static int dnv_setup(struct mid8250 *mid, struct uart_port *p)
 {
 	struct hsu_dma_chip *chip = &mid->dma_chip;
 	struct pci_dev *pdev = to_pci_dev(p->dev);
+	unsigned int bar = FL_GET_BASE(mid->board->flags);
 	int ret;
 
 	chip->dev = &pdev->dev;
 	chip->irq = pdev->irq;
 	chip->regs = p->membase;
-	chip->length = pci_resource_len(pdev, 0);
+	chip->length = pci_resource_len(pdev, bar);
 	chip->offset = DNV_DMA_CHAN_OFFSET;
 
 	/* Falling back to PIO mode if DMA probing fails */
@@ -217,6 +221,7 @@ static int mid8250_probe(struct pci_dev *pdev, const struct pci_device_id *id)
 {
 	struct uart_8250_port uart;
 	struct mid8250 *mid;
+	unsigned int bar;
 	int ret;
 
 	ret = pcim_enable_device(pdev);
@@ -230,6 +235,7 @@ static int mid8250_probe(struct pci_dev *pdev, const struct pci_device_id *id)
 		return -ENOMEM;
 
 	mid->board = (struct mid8250_board *)id->driver_data;
+	bar = FL_GET_BASE(mid->board->flags);
 
 	memset(&uart, 0, sizeof(struct uart_8250_port));
 
@@ -242,8 +248,8 @@ static int mid8250_probe(struct pci_dev *pdev, const struct pci_device_id *id)
 	uart.port.flags = UPF_SHARE_IRQ | UPF_FIXED_PORT | UPF_FIXED_TYPE;
 	uart.port.set_termios = mid8250_set_termios;
 
-	uart.port.mapbase = pci_resource_start(pdev, 0);
-	uart.port.membase = pcim_iomap(pdev, 0, 0);
+	uart.port.mapbase = pci_resource_start(pdev, bar);
+	uart.port.membase = pcim_iomap(pdev, bar, 0);
 	if (!uart.port.membase)
 		return -ENOMEM;
 
@@ -282,18 +288,21 @@ static void mid8250_remove(struct pci_dev *pdev)
 }
 
 static const struct mid8250_board pnw_board = {
+	.flags = FL_BASE0,
 	.freq = 50000000,
 	.base_baud = 115200,
 	.setup = pnw_setup,
 };
 
 static const struct mid8250_board tng_board = {
+	.flags = FL_BASE0,
 	.freq = 38400000,
 	.base_baud = 1843200,
 	.setup = tng_setup,
 };
 
 static const struct mid8250_board dnv_board = {
+	.flags = FL_BASE1,
 	.freq = 133333333,
 	.base_baud = 115200,
 	.setup = dnv_setup,
diff --git a/drivers/tty/serial/8250/8250_pci.c b/drivers/tty/serial/8250/8250_pci.c
index 7cd6f9a90542..c1d4a8fa9be8 100644
--- a/drivers/tty/serial/8250/8250_pci.c
+++ b/drivers/tty/serial/8250/8250_pci.c
@@ -1401,6 +1401,9 @@ byt_set_termios(struct uart_port *p, struct ktermios *termios,
 	unsigned long m, n;
 	u32 reg;
 
+	/* Gracefully handle the B0 case: fall back to B9600 */
+	fuart = fuart ? fuart : 9600 * 16;
+
 	/* Get Fuart closer to Fref */
 	fuart *= rounddown_pow_of_two(fref / fuart);
 
diff --git a/drivers/tty/serial/atmel_serial.c b/drivers/tty/serial/atmel_serial.c
index 94294558943c..7bbadd176c74 100644
--- a/drivers/tty/serial/atmel_serial.c
+++ b/drivers/tty/serial/atmel_serial.c
@@ -277,6 +277,13 @@ static bool atmel_use_dma_rx(struct uart_port *port)
 	return atmel_port->use_dma_rx;
 }
 
+static bool atmel_use_fifo(struct uart_port *port)
+{
+	struct atmel_uart_port *atmel_port = to_atmel_uart_port(port);
+
+	return atmel_port->fifo_size;
+}
+
 static unsigned int atmel_get_lines_status(struct uart_port *port)
 {
 	struct atmel_uart_port *atmel_port = to_atmel_uart_port(port);
@@ -2169,7 +2176,12 @@ static void atmel_set_termios(struct uart_port *port, struct ktermios *termios,
 		mode |= ATMEL_US_USMODE_RS485;
 	} else if (termios->c_cflag & CRTSCTS) {
 		/* RS232 with hardware handshake (RTS/CTS) */
-		mode |= ATMEL_US_USMODE_HWHS;
+		if (atmel_use_dma_rx(port) && !atmel_use_fifo(port)) {
+			dev_info(port->dev, "not enabling hardware flow control because DMA is used");
+			termios->c_cflag &= ~CRTSCTS;
+		} else {
+			mode |= ATMEL_US_USMODE_HWHS;
+		}
 	} else {
 		/* RS232 without hadware handshake */
 		mode |= ATMEL_US_USMODE_NORMAL;
diff --git a/drivers/tty/serial/samsung.c b/drivers/tty/serial/samsung.c
index d72cd736bdc6..8320173af846 100644
--- a/drivers/tty/serial/samsung.c
+++ b/drivers/tty/serial/samsung.c
@@ -1263,6 +1263,8 @@ static void s3c24xx_serial_set_termios(struct uart_port *port,
 	/* check to see if we need  to change clock source */
 
 	if (ourport->baudclk != clk) {
+		clk_prepare_enable(clk);
+
 		s3c24xx_serial_setsource(port, clk_sel);
 
 		if (!IS_ERR(ourport->baudclk)) {
@@ -1270,8 +1272,6 @@ static void s3c24xx_serial_set_termios(struct uart_port *port,
 			ourport->baudclk = ERR_PTR(-EINVAL);
 		}
 
-		clk_prepare_enable(clk);
-
 		ourport->baudclk = clk;
 		ourport->baudclk_rate = clk ? clk_get_rate(clk) : 0;
 	}