Merge branch 'perf/core' into perf/uprobes

Merge in latest upstream (and the latest perf development tree),
to prepare for tooling changes, and also to pick up v3.4 MM
changes that the uprobes code needs to take care of.

Signed-off-by: Ingo Molnar <mingo@kernel.org>

1 files changed, 18 insertions, 21 deletions

diff --git a/drivers/hwmon/ads7871.c b/drivers/hwmon/ads7871.c
index 04450f8bf5da..e65c6e45d36b 100644
--- a/drivers/hwmon/ads7871.c
+++ b/drivers/hwmon/ads7871.c
@@ -34,9 +34,11 @@
 #define REG_SER_CONTROL 24 /*Serial Interface Control Register*/
 #define REG_ID		31 /*ID Register*/
 
-/*From figure 17 in the datasheet
-* These bits get ORed with the address to form
-* the instruction byte */
+/*
+ * From figure 17 in the datasheet
+ * These bits get ORed with the address to form
+ * the instruction byte
+ */
 /*Instruction Bit masks*/
 #define INST_MODE_bm	(1<<7)
 #define INST_READ_bm	(1<<6)
@@ -105,8 +107,10 @@ static ssize_t show_voltage(struct device *dev,
 	uint8_t channel, mux_cnv;
 
 	channel = attr->index;
-	/*TODO: add support for conversions
-	 *other than single ended with a gain of 1*/
+	/*
+	 * TODO: add support for conversions
+	 * other than single ended with a gain of 1
+	 */
 	/*MUX_M3_bm forces single ended*/
 	/*This is also where the gain of the PGA would be set*/
 	ads7871_write_reg8(spi, REG_GAIN_MUX,
@@ -114,8 +118,10 @@ static ssize_t show_voltage(struct device *dev,
 
 	ret = ads7871_read_reg8(spi, REG_GAIN_MUX);
 	mux_cnv = ((ret & MUX_CNV_bm)>>MUX_CNV_bv);
-	/*on 400MHz arm9 platform the conversion
-	 *is already done when we do this test*/
+	/*
+	 * on 400MHz arm9 platform the conversion
+	 * is already done when we do this test
+	 */
 	while ((i < 2) && mux_cnv) {
 		i++;
 		ret = ads7871_read_reg8(spi, REG_GAIN_MUX);
@@ -179,8 +185,10 @@ static int __devinit ads7871_probe(struct spi_device *spi)
 	ret = ads7871_read_reg8(spi, REG_OSC_CONTROL);
 
 	dev_dbg(&spi->dev, "REG_OSC_CONTROL write:%x, read:%x\n", val, ret);
-	/*because there is no other error checking on an SPI bus
-	we need to make sure we really have a chip*/
+	/*
+	 * because there is no other error checking on an SPI bus
+	 * we need to make sure we really have a chip
+	 */
 	if (val != ret) {
 		err = -ENODEV;
 		goto exit;
@@ -234,18 +242,7 @@ static struct spi_driver ads7871_driver = {
 	.remove = __devexit_p(ads7871_remove),
 };
 
-static int __init ads7871_init(void)
-{
-	return spi_register_driver(&ads7871_driver);
-}
-
-static void __exit ads7871_exit(void)
-{
-	spi_unregister_driver(&ads7871_driver);
-}
-
-module_init(ads7871_init);
-module_exit(ads7871_exit);
+module_spi_driver(ads7871_driver);
 
 MODULE_AUTHOR("Paul Thomas <pthomas8589@gmail.com>");
 MODULE_DESCRIPTION("TI ADS7871 A/D driver");