diff options
| author | Marijn Suijten <marijn.suijten@somainline.org> | 2021-04-06 23:47:24 +0200 |
|---|---|---|
| committer | Greg Kroah-Hartman <gregkh@linuxfoundation.org> | 2021-05-22 10:38:18 +0200 |
| commit | 69bdad127926eb25bcd78a6a3ecd7e37782ba2ae (patch) | |
| tree | 7017ae24cb7a1bdd7ca745476bba686a265ed5bd /drivers/gpu | |
| parent | 213c6ba76578a9a7f3a57116394a4d5f5fbd9bd6 (diff) | |
drm/msm/mdp5: Configure PP_SYNC_HEIGHT to double the vtotal
[ Upstream commit 2ad52bdb220de5ab348098e3482b01235d15a842 ]
Leaving this at a close-to-maximum register value 0xFFF0 means it takes
very long for the MDSS to generate a software vsync interrupt when the
hardware TE interrupt doesn't arrive. Configuring this to double the
vtotal (like some downstream kernels) leads to a frame to take at most
twice before the vsync signal, until hardware TE comes up.
In this case the hardware interrupt responsible for providing this
signal - "disp-te" gpio - is not hooked up to the mdp5 vsync/pp logic at
all. This solves severe panel update issues observed on at least the
Xperia Loire and Tone series, until said gpio is properly hooked up to
an irq.
Suggested-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@somainline.org>
Signed-off-by: Marijn Suijten <marijn.suijten@somainline.org>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@somainline.org>
Link: https://lore.kernel.org/r/20210406214726.131534-2-marijn.suijten@somainline.org
Signed-off-by: Rob Clark <robdclark@chromium.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Diffstat (limited to 'drivers/gpu')
| -rw-r--r-- | drivers/gpu/drm/msm/mdp/mdp5/mdp5_cmd_encoder.c | 10 |
1 files changed, 9 insertions, 1 deletions
diff --git a/drivers/gpu/drm/msm/mdp/mdp5/mdp5_cmd_encoder.c b/drivers/gpu/drm/msm/mdp/mdp5/mdp5_cmd_encoder.c index 8e6c9b598a57..d8c7b8a6a418 100644 --- a/drivers/gpu/drm/msm/mdp/mdp5/mdp5_cmd_encoder.c +++ b/drivers/gpu/drm/msm/mdp/mdp5/mdp5_cmd_encoder.c @@ -128,9 +128,17 @@ static int pingpong_tearcheck_setup(struct drm_encoder *encoder, | MDP5_PP_SYNC_CONFIG_VSYNC_IN_EN; cfg |= MDP5_PP_SYNC_CONFIG_VSYNC_COUNT(vclks_line); + /* + * Tearcheck emits a blanking signal every vclks_line * vtotal * 2 ticks on + * the vsync_clk equating to roughly half the desired panel refresh rate. + * This is only necessary as stability fallback if interrupts from the + * panel arrive too late or not at all, but is currently used by default + * because these panel interrupts are not wired up yet. + */ mdp5_write(mdp5_kms, REG_MDP5_PP_SYNC_CONFIG_VSYNC(pp_id), cfg); mdp5_write(mdp5_kms, - REG_MDP5_PP_SYNC_CONFIG_HEIGHT(pp_id), 0xfff0); + REG_MDP5_PP_SYNC_CONFIG_HEIGHT(pp_id), (2 * mode->vtotal)); + mdp5_write(mdp5_kms, REG_MDP5_PP_VSYNC_INIT_VAL(pp_id), mode->vdisplay); mdp5_write(mdp5_kms, REG_MDP5_PP_RD_PTR_IRQ(pp_id), mode->vdisplay + 1); |