Merge branch 'omap/dt' into next/drivers

Needed for the omap timer changes.

Signed-off-by: Arnd Bergmann <arnd@arndb.de>

9 files changed, 109 insertions, 3 deletions

diff --git a/Documentation/devicetree/bindings/arm/atmel-at91.txt b/Documentation/devicetree/bindings/arm/atmel-at91.txt
index ecc81e368715..d187e9f7cf1c 100644
--- a/Documentation/devicetree/bindings/arm/atmel-at91.txt
+++ b/Documentation/devicetree/bindings/arm/atmel-at91.txt
@@ -8,7 +8,7 @@ PIT Timer required properties:
   shared across all System Controller members.
 
 TC/TCLIB Timer required properties:
-- compatible: Should be "atmel,<chip>-pit".
+- compatible: Should be "atmel,<chip>-tcb".
   <chip> can be "at91rm9200" or "at91sam9x5"
 - reg: Should contain registers location and length
 - interrupts: Should contain all interrupts for the TC block
diff --git a/Documentation/devicetree/bindings/arm/omap/counter.txt b/Documentation/devicetree/bindings/arm/omap/counter.txt
new file mode 100644
index 000000000000..5bd8aa091315
--- /dev/null
+++ b/Documentation/devicetree/bindings/arm/omap/counter.txt
@@ -0,0 +1,15 @@
+OMAP Counter-32K bindings
+
+Required properties:
+- compatible:	Must be "ti,omap-counter32k" for OMAP controllers
+- reg:		Contains timer register address range (base address and length)
+- ti,hwmods:	Name of the hwmod associated to the counter, which is typically
+		"counter_32k"
+
+Example:
+
+counter32k: counter@4a304000 {
+	compatible = "ti,omap-counter32k";
+	reg = <0x4a304000 0x20>;
+	ti,hwmods = "counter_32k";
+};
diff --git a/Documentation/devicetree/bindings/arm/omap/timer.txt b/Documentation/devicetree/bindings/arm/omap/timer.txt
new file mode 100644
index 000000000000..8732d4d41f8b
--- /dev/null
+++ b/Documentation/devicetree/bindings/arm/omap/timer.txt
@@ -0,0 +1,31 @@
+OMAP Timer bindings
+
+Required properties:
+- compatible:		Must be "ti,omap2-timer" for OMAP2+ controllers.
+- reg:			Contains timer register address range (base address and
+			length).
+- interrupts: 		Contains the interrupt information for the timer. The
+			format is being dependent on which interrupt controller
+			the OMAP device uses.
+- ti,hwmods:		Name of the hwmod associated to the timer, "timer<X>",
+			where <X> is the instance number of the timer from the
+			HW spec.
+
+Optional properties:
+- ti,timer-alwon:	Indicates the timer is in an alway-on power domain.
+- ti,timer-dsp:		Indicates the timer can interrupt the on-chip DSP in
+			addition to the ARM CPU.
+- ti,timer-pwm: 	Indicates the timer can generate a PWM output.
+- ti,timer-secure: 	Indicates the timer is reserved on a secure OMAP device
+			and therefore cannot be used by the kernel.
+
+Example:
+
+timer12: timer@48304000 {
+	compatible = "ti,omap2-timer";
+	reg = <0x48304000 0x400>;
+	interrupts = <95>;
+	ti,hwmods = "timer12"
+	ti,timer-alwon;
+	ti,timer-secure;
+};
diff --git a/Documentation/devicetree/bindings/bus/omap-ocp2scp.txt b/Documentation/devicetree/bindings/bus/omap-ocp2scp.txt
index d2fe064a828b..63dd8051521c 100644
--- a/Documentation/devicetree/bindings/bus/omap-ocp2scp.txt
+++ b/Documentation/devicetree/bindings/bus/omap-ocp2scp.txt
@@ -2,9 +2,27 @@
 
 properties:
 - compatible : Should be "ti,omap-ocp2scp"
+- reg : Address and length of the register set for the device
 - #address-cells, #size-cells : Must be present if the device has sub-nodes
 - ranges : the child address space are mapped 1:1 onto the parent address space
 - ti,hwmods : must be "ocp2scp_usb_phy"
 
 Sub-nodes:
 All the devices connected to ocp2scp are described using sub-node to ocp2scp
+
+ocp2scp@4a0ad000 {
+	compatible = "ti,omap-ocp2scp";
+	reg = <0x4a0ad000 0x1f>;
+	#address-cells = <1>;
+	#size-cells = <1>;
+	ranges;
+	ti,hwmods = "ocp2scp_usb_phy";
+
+	subnode1 {
+	...
+	};
+
+	subnode2 {
+	...
+	};
+};
diff --git a/Documentation/devicetree/bindings/i2c/trivial-devices.txt b/Documentation/devicetree/bindings/i2c/trivial-devices.txt
index 2f5322b119eb..446859fcdca4 100644
--- a/Documentation/devicetree/bindings/i2c/trivial-devices.txt
+++ b/Documentation/devicetree/bindings/i2c/trivial-devices.txt
@@ -55,5 +55,7 @@ st-micro,24c256		i2c serial eeprom  (24cxx)
 stm,m41t00		Serial Access TIMEKEEPER
 stm,m41t62		Serial real-time clock (RTC) with alarm
 stm,m41t80		M41T80 - SERIAL ACCESS RTC WITH ALARMS
+taos,tsl2550		Ambient Light Sensor with SMBUS/Two Wire Serial Interface
 ti,tsc2003		I2C Touch-Screen Controller
 ti,tmp102		Low Power Digital Temperature Sensor with SMBUS/Two Wire Serial Interface
+ti,tmp275		Digital Temperature Sensor
diff --git a/Documentation/devicetree/bindings/input/touchscreen/egalax-ts.txt b/Documentation/devicetree/bindings/input/touchscreen/egalax-ts.txt
new file mode 100644
index 000000000000..df70318a617f
--- /dev/null
+++ b/Documentation/devicetree/bindings/input/touchscreen/egalax-ts.txt
@@ -0,0 +1,19 @@
+* EETI eGalax Multiple Touch Controller
+
+Required properties:
+- compatible: must be "eeti,egalax_ts"
+- reg: i2c slave address
+- interrupt-parent: the phandle for the interrupt controller
+- interrupts: touch controller interrupt
+- wakeup-gpios: the gpio pin to be used for waking up the controller
+  as well as uased as irq pin
+
+Example:
+
+	egalax_ts@04 {
+		compatible = "eeti,egalax_ts";
+		reg = <0x04>;
+		interrupt-parent = <&gpio1>;
+		interrupts = <9 2>;
+		wakeup-gpios = <&gpio1 9 0>;
+	};
diff --git a/Documentation/devicetree/bindings/pinctrl/nvidia,tegra20-pinmux.txt b/Documentation/devicetree/bindings/pinctrl/nvidia,tegra20-pinmux.txt
index c8e578263ce2..683fde93c4fb 100644
--- a/Documentation/devicetree/bindings/pinctrl/nvidia,tegra20-pinmux.txt
+++ b/Documentation/devicetree/bindings/pinctrl/nvidia,tegra20-pinmux.txt
@@ -93,7 +93,7 @@ Valid values for pin and group names are:
 
     With some exceptions, these support nvidia,high-speed-mode,
     nvidia,schmitt, nvidia,low-power-mode, nvidia,pull-down-strength,
-    nvidia,pull-up-strength, nvidia,slew_rate-rising, nvidia,slew_rate-falling.
+    nvidia,pull-up-strength, nvidia,slew-rate-rising, nvidia,slew-rate-falling.
 
     drive_ao1, drive_ao2, drive_at1, drive_at2, drive_cdev1, drive_cdev2,
     drive_csus, drive_dap1, drive_dap2, drive_dap3, drive_dap4, drive_dbg,
diff --git a/Documentation/devicetree/bindings/pinctrl/nvidia,tegra30-pinmux.txt b/Documentation/devicetree/bindings/pinctrl/nvidia,tegra30-pinmux.txt
index c275b70349c1..6f426ed7009e 100644
--- a/Documentation/devicetree/bindings/pinctrl/nvidia,tegra30-pinmux.txt
+++ b/Documentation/devicetree/bindings/pinctrl/nvidia,tegra30-pinmux.txt
@@ -83,7 +83,7 @@ Valid values for pin and group names are:
   drive groups:
 
     These all support nvidia,pull-down-strength, nvidia,pull-up-strength,
-    nvidia,slew_rate-rising, nvidia,slew_rate-falling. Most but not all
+    nvidia,slew-rate-rising, nvidia,slew-rate-falling. Most but not all
     support nvidia,high-speed-mode, nvidia,schmitt, nvidia,low-power-mode.
 
     ao1, ao2, at1, at2, at3, at4, at5, cdev1, cdev2, cec, crt, csus, dap1,
diff --git a/Documentation/devicetree/bindings/usb/am33xx-usb.txt b/Documentation/devicetree/bindings/usb/am33xx-usb.txt
index ca8fa56e9f03..707c1a2dae06 100644
--- a/Documentation/devicetree/bindings/usb/am33xx-usb.txt
+++ b/Documentation/devicetree/bindings/usb/am33xx-usb.txt
@@ -1,5 +1,7 @@
 AM33XX MUSB GLUE
  - compatible : Should be "ti,musb-am33xx"
+ - reg : offset and length of register sets, first usbss, then for musb instances
+ - interrupts : usbss, musb instance interrupts in order
  - ti,hwmods : must be "usb_otg_hs"
  - multipoint : Should be "1" indicating the musb controller supports
    multipoint. This is a MUSB configuration-specific setting.
@@ -12,3 +14,22 @@ AM33XX MUSB GLUE
    represents PERIPHERAL.
  - power : Should be "250". This signifies the controller can supply upto
    500mA when operating in host mode.
+
+Example:
+
+usb@47400000  {
+	compatible = "ti,musb-am33xx";
+	reg = <0x47400000 0x1000	/* usbss */
+	       0x47401000 0x800		/* musb instance 0 */
+	       0x47401800 0x800>;	/* musb instance 1 */
+	interrupts = <17		/* usbss */
+		      18		/* musb instance 0 */
+		      19>;		/* musb instance 1 */
+	multipoint = <1>;
+	num-eps = <16>;
+	ram-bits = <12>;
+	port0-mode = <3>;
+	port1-mode = <3>;
+	power = <250>;
+	ti,hwmods = "usb_otg_hs";
+};