Merge branch 'uprobes-v7' of git://git.linaro.org/people/dave.long/linux into devel-stable

This patch series adds basic uprobes support to ARM. It is based on
patches developed earlier by Rabin Vincent. That approach of adding
hooks into the kprobes instruction parsing code was not well received.
This approach separates the ARM instruction parsing code in kprobes out
into a separate set of functions which can be used by both kprobes and
uprobes. Both kprobes and uprobes then provide their own semantic action
tables to process the results of the parsing.

3 files changed, 69 insertions, 7 deletions

diff --git a/Documentation/devicetree/bindings/arm/omap/omap.txt b/Documentation/devicetree/bindings/arm/omap/omap.txt
index 34dc40cffdfd..af9b4a0d902b 100644
--- a/Documentation/devicetree/bindings/arm/omap/omap.txt
+++ b/Documentation/devicetree/bindings/arm/omap/omap.txt
@@ -91,7 +91,7 @@ Boards:
   compatible = "ti,omap3-beagle", "ti,omap3"
 
 - OMAP3 Tobi with Overo : Commercial expansion board with daughter board
-  compatible = "ti,omap3-tobi", "ti,omap3-overo", "ti,omap3"
+  compatible = "gumstix,omap3-overo-tobi", "gumstix,omap3-overo", "ti,omap3"
 
 - OMAP4 SDP : Software Development Board
   compatible = "ti,omap4-sdp", "ti,omap4430"
diff --git a/Documentation/devicetree/bindings/dma/fsl-imx-sdma.txt b/Documentation/devicetree/bindings/dma/fsl-imx-sdma.txt
index 68b83ecc3850..ee9be9961524 100644
--- a/Documentation/devicetree/bindings/dma/fsl-imx-sdma.txt
+++ b/Documentation/devicetree/bindings/dma/fsl-imx-sdma.txt
@@ -1,12 +1,16 @@
 * Freescale Smart Direct Memory Access (SDMA) Controller for i.MX
 
 Required properties:
-- compatible : Should be "fsl,imx31-sdma", "fsl,imx31-to1-sdma",
-  "fsl,imx31-to2-sdma", "fsl,imx35-sdma", "fsl,imx35-to1-sdma",
-  "fsl,imx35-to2-sdma", "fsl,imx51-sdma", "fsl,imx53-sdma" or
-  "fsl,imx6q-sdma". The -to variants should be preferred since they
-  allow to determnine the correct ROM script addresses needed for
-  the driver to work without additional firmware.
+- compatible : Should be one of
+      "fsl,imx25-sdma"
+      "fsl,imx31-sdma", "fsl,imx31-to1-sdma", "fsl,imx31-to2-sdma"
+      "fsl,imx35-sdma", "fsl,imx35-to1-sdma", "fsl,imx35-to2-sdma"
+      "fsl,imx51-sdma"
+      "fsl,imx53-sdma"
+      "fsl,imx6q-sdma"
+  The -to variants should be preferred since they allow to determnine the
+  correct ROM script addresses needed for the driver to work without additional
+  firmware.
 - reg : Should contain SDMA registers location and length
 - interrupts : Should contain SDMA interrupt
 - #dma-cells : Must be <3>.
diff --git a/Documentation/devicetree/bindings/net/sti-dwmac.txt b/Documentation/devicetree/bindings/net/sti-dwmac.txt
new file mode 100644
index 000000000000..3dd3d0bf112f
--- /dev/null
+++ b/Documentation/devicetree/bindings/net/sti-dwmac.txt
@@ -0,0 +1,58 @@
+STMicroelectronics SoC DWMAC glue layer controller
+
+The device node has following properties.
+
+Required properties:
+ - compatible	: Can be "st,stih415-dwmac", "st,stih416-dwmac" or
+   "st,stid127-dwmac".
+ - reg		: Offset of the glue configuration register map in system
+   configuration regmap pointed by st,syscon property and size.
+
+ - reg-names	: Should be "sti-ethconf".
+
+ - st,syscon	: Should be phandle to system configuration node which
+   encompases this glue registers.
+
+ - st,tx-retime-src: On STi Parts for Giga bit speeds, 125Mhz clocks can be
+   wired up in from different sources. One via TXCLK pin and other via CLK_125
+   pin. This wiring is totally board dependent. However the retiming glue
+   logic should be configured accordingly. Possible values for this property
+
+	   "txclk" - if 125Mhz clock is wired up via txclk line.
+	   "clk_125" - if 125Mhz clock is wired up via clk_125 line.
+
+   This property is only valid for Giga bit setup( GMII, RGMII), and it is
+   un-used for non-giga bit (MII and RMII) setups. Also note that internal
+   clockgen can not generate stable 125Mhz clock.
+
+ - st,ext-phyclk: This boolean property indicates who is generating the clock
+  for tx and rx. This property is only valid for RMII case where the clock can
+  be generated from the MAC or PHY.
+
+ - clock-names: should be "sti-ethclk".
+ - clocks: Should point to ethernet clockgen which can generate phyclk.
+
+
+Example:
+
+ethernet0: dwmac@fe810000 {
+	device_type 	= "network";
+	compatible	= "st,stih416-dwmac", "snps,dwmac", "snps,dwmac-3.710";
+	reg 		= <0xfe810000 0x8000>, <0x8bc 0x4>;
+	reg-names	= "stmmaceth", "sti-ethconf";
+	interrupts	= <0 133 0>, <0 134 0>, <0 135 0>;
+	interrupt-names	= "macirq", "eth_wake_irq", "eth_lpi";
+	phy-mode	= "mii";
+
+	st,syscon	= <&syscfg_rear>;
+
+	snps,pbl 	= <32>;
+	snps,mixed-burst;
+
+	resets		= <&softreset STIH416_ETH0_SOFTRESET>;
+	reset-names	= "stmmaceth";
+	pinctrl-0	= <&pinctrl_mii0>;
+	pinctrl-names 	= "default";
+	clocks		= <&CLK_S_GMAC0_PHY>;
+	clock-names	= "stmmaceth";
+};