4 files changed, 42 insertions, 10 deletions
diff --git a/Documentation/networking/bonding.txt b/Documentation/networking/bonding.txt
index 334b49ef02d1..5a6e70483ced 100644
--- a/Documentation/networking/bonding.txt
+++ b/Documentation/networking/bonding.txt
@@ -191,11 +191,12 @@ ad_actor_sys_prio
 ad_actor_system
 
 	In an AD system, this specifies the mac-address for the actor in
-	protocol packet exchanges (LACPDUs). The value cannot be NULL or
-	multicast. It is preferred to have the local-admin bit set for this
-	mac but driver does not enforce it. If the value is not given then
-	system defaults to using the masters' mac address as actors' system
-	address.
+	protocol packet exchanges (LACPDUs). The value cannot be a multicast
+	address. If the all-zeroes MAC is specified, bonding will internally
+	use the MAC of the bond itself. It is preferred to have the
+	local-admin bit set for this mac but driver does not enforce it. If
+	the value is not given then system defaults to using the masters'
+	mac address as actors' system address.
 
 	This parameter has effect only in 802.3ad mode and is available through
 	SysFs interface.
diff --git a/Documentation/networking/filter.txt b/Documentation/networking/filter.txt
index 96da119a47e7..4e3e22b053cc 100644
--- a/Documentation/networking/filter.txt
+++ b/Documentation/networking/filter.txt
@@ -907,6 +907,10 @@ If BPF_CLASS(code) == BPF_JMP, BPF_OP(code) is one of:
   BPF_JSGE  0x70  /* eBPF only: signed '>=' */
   BPF_CALL  0x80  /* eBPF only: function call */
   BPF_EXIT  0x90  /* eBPF only: function return */
+  BPF_JLT   0xa0  /* eBPF only: unsigned '<' */
+  BPF_JLE   0xb0  /* eBPF only: unsigned '<=' */
+  BPF_JSLT  0xc0  /* eBPF only: signed '<' */
+  BPF_JSLE  0xd0  /* eBPF only: signed '<=' */
 
 So BPF_ADD | BPF_X | BPF_ALU means 32-bit addition in both classic BPF
 and eBPF. There are only two registers in classic BPF, so it means A += X.
diff --git a/Documentation/networking/ip-sysctl.txt b/Documentation/networking/ip-sysctl.txt
index a7516e4c8ce8..3801784f47be 100644
--- a/Documentation/networking/ip-sysctl.txt
+++ b/Documentation/networking/ip-sysctl.txt
@@ -883,12 +883,14 @@ icmp_ratelimit - INTEGER
 icmp_msgs_per_sec - INTEGER
 	Limit maximal number of ICMP packets sent per second from this host.
 	Only messages whose type matches icmp_ratemask (see below) are
-	controlled by this limit.
+	controlled by this limit. For security reasons, the precise count
+	of messages per second is randomized.
 	Default: 1000
 
 icmp_msgs_burst - INTEGER
 	icmp_msgs_per_sec controls number of ICMP packets sent per second,
 	while icmp_msgs_burst controls the burst size of these packets.
+	For security reasons, the precise burst size is randomized.
 	Default: 50
 
 icmp_ratemask - INTEGER
@@ -1229,6 +1231,18 @@ promote_secondaries - BOOLEAN
 	promote a corresponding secondary IP address instead of
 	removing all the corresponding secondary IP addresses.
 
+drop_unicast_in_l2_multicast - BOOLEAN
+	Drop any unicast IP packets that are received in link-layer
+	multicast (or broadcast) frames.
+	This behavior (for multicast) is actually a SHOULD in RFC
+	1122, but is disabled by default for compatibility reasons.
+	Default: off (0)
+
+drop_gratuitous_arp - BOOLEAN
+	Drop all gratuitous ARP frames, for example if there's a known
+	good ARP proxy on the network and such frames need not be used
+	(or in the case of 802.11, must not be used to prevent attacks.)
+	Default: off (0)
 
 tag - INTEGER
 	Allows you to write a number, which can be used as required.
@@ -1692,6 +1706,19 @@ stable_secret - IPv6 address
 
 	By default the stable secret is unset.
 
+drop_unicast_in_l2_multicast - BOOLEAN
+	Drop any unicast IPv6 packets that are received in link-layer
+	multicast (or broadcast) frames.
+
+	By default this is turned off.
+
+drop_unsolicited_na - BOOLEAN
+	Drop all unsolicited neighbor advertisements, for example if there's
+	a known good NA proxy on the network and such frames need not be used
+	(or in the case of 802.11, must not be used to prevent attacks.)
+
+	By default this is turned off.
+
 icmp/*:
 ratelimit - INTEGER
 	Limit the maximal rates for sending ICMPv6 packets.
diff --git a/Documentation/networking/l2tp.txt b/Documentation/networking/l2tp.txt
index 4650a00ed012..9bc271cdc9a8 100644
--- a/Documentation/networking/l2tp.txt
+++ b/Documentation/networking/l2tp.txt
@@ -177,10 +177,10 @@ setsockopt on the PPPoX socket to set a debug mask.
 
 The following debug mask bits are available:
 
-PPPOL2TP_MSG_DEBUG    verbose debug (if compiled in)
-PPPOL2TP_MSG_CONTROL  userspace - kernel interface
-PPPOL2TP_MSG_SEQ      sequence numbers handling
-PPPOL2TP_MSG_DATA     data packets
+L2TP_MSG_DEBUG    verbose debug (if compiled in)
+L2TP_MSG_CONTROL  userspace - kernel interface
+L2TP_MSG_SEQ      sequence numbers handling
+L2TP_MSG_DATA     data packets
 
 If enabled, files under a l2tp debugfs directory can be used to dump
 kernel state about L2TP tunnels and sessions. To access it, the