diff options
Diffstat (limited to 'wifi/WCNSS_qcom_cfg.ini')
-rw-r--r-- | wifi/WCNSS_qcom_cfg.ini | 635 |
1 files changed, 635 insertions, 0 deletions
diff --git a/wifi/WCNSS_qcom_cfg.ini b/wifi/WCNSS_qcom_cfg.ini new file mode 100644 index 0000000..083683b --- /dev/null +++ b/wifi/WCNSS_qcom_cfg.ini @@ -0,0 +1,635 @@ +# This file allows user to override the factory + +# defaults for the WLAN Driver + + +# Enable IMPS or not +gEnableImps=1 + +# Enable/Disable Idle Scan + +gEnableIdleScan=0 + + +# Increase sleep duration (seconds) during IMPS +# 0 implies no periodic wake up from IMPS. Periodic wakeup is +# unnecessary if Idle Scan is disabled. +gImpsModSleepTime=0 + + +# Enable BMPS or not +gEnableBmps=1 + +# Enable suspend or not + +# 1: Enable standby, 2: Enable Deep sleep, 3: Enable Mcast/Bcast Filter + +gEnableSuspend=3 + + +# Phy Mode (auto, b, g, n, etc) +# Valid values are 0-9, with 0 = Auto, 4 = 11n, 9 = 11ac +# 1 = 11abg, 2 = 11b, 3 = 11g, 5 = 11g only, 6 = 11n only +# 7 = 11b only 8 = 11ac only. +gDot11Mode=0 + + +# CSR Roaming Enable(1) Disable(0) + +gRoamingTime=0 + + +# Assigned MAC Addresses - This will be used until NV items are in place + +# Each byte of MAC address is represented in Hex format as XX + +Intf0MacAddress=000AF58989FF +Intf1MacAddress=000AF58989FE +Intf2MacAddress=000AF58989FD + +Intf3MacAddress=000AF58989FC + + +# UAPSD service interval for VO,VI, BE, BK traffic + +InfraUapsdVoSrvIntv=0 + +InfraUapsdViSrvIntv=0 + +InfraUapsdBeSrvIntv=0 + +InfraUapsdBkSrvIntv=0 + +# Flag to allow STA send AddTspec even when ACM is Off +gAddTSWhenACMIsOff=1 + +# Make 1x1 the default antenna configuration + +gNumRxAnt=1 + + +# Beacon filtering frequency (unit in beacon intervals) + +gNthBeaconFilter=50 + + +# Enable WAPI or not + +WAPIIsEnabled=1 + + +# Flags to filter Mcast abd Bcast RX packets. + +# Value 0: No filtering, 1: Filter all Multicast. + +# 2: Filter all Broadcast. 3: Filter all Mcast abd Bcast + +McastBcastFilter=3 + + +#Flag to enable HostARPOffload feature or not + +hostArpOffload=1 + +#Flag to enable TCPChkSumOffld feature or not + +gEnableTCPChkSumOffld=1 + +#Flag to enable HostNSOffload feature or not + +hostNSOffload=1 + +#Flag to enable IPChkSumOffld feature or not + +gEnableIPChecksumOffload=1 + +#SoftAP Related Parameters + +# AP MAc addr + +gAPMacAddr=000AF589dcab + + +# 802.11n Protection flag + +gEnableApProt=1 + + +#Enable OBSS protection + +gEnableApOBSSProt=1 + + +#Enable/Disable UAPSD for SoftAP + +gEnableApUapsd=1 + + +# Fixed Rate + +gFixedRate=0 + + +# Maximum Tx power + +# gTxPowerCap=30 + + +# Fragmentation Threshold + +# gFragmentationThreshold=2346 + + +# RTS threshold + +RTSThreshold=1048576 + + +# Intra-BSS forward + +gDisableIntraBssFwd=0 + + +# WMM Enable/Disable + +WmmIsEnabled=0 + + +# 802.11d support + +g11dSupportEnabled=1 + +# 802.11h support + +g11hSupportEnabled=1 + +# DFS Master Capability +gEnableDFSMasterCap=1 + +# ESE Support and fast transition +EseEnabled=0 +ImplicitQosIsEnabled=0 +gNeighborScanTimerPeriod=200 + +gNeighborLookupThreshold=76 +gNeighborReassocThreshold=81 + +gNeighborScanChannelMinTime=20 +gNeighborScanChannelMaxTime=30 +gMaxNeighborReqTries=3 + +# Legacy (non-ESE, non-802.11r) Fast Roaming Support +# To enable, set FastRoamEnabled=1 +# To disable, set FastRoamEnabled=0 +FastRoamEnabled=1 + +#Check if the AP to which we are roaming is better than current AP in terms of RSSI. +#Checking is disabled if set to Zero.Otherwise it will use this value as to how better +#the RSSI of the new/roamable AP should be for roaming +RoamRssiDiff=5 + +# If the RSSI of any available candidate is better than currently associated +# AP by at least gImmediateRoamRssiDiff, then being to roam immediately (without +# registering for reassoc threshold). +# NOTE: Value of 0 means that we would register for reassoc threshold. +gImmediateRoamRssiDiff=10 + +# To enable, set gRoamIntraBand=1 (Roaming within band) +# To disable, set gRoamIntraBand=0 (Roaming across band) +gRoamIntraBand=0 + +# SAP Country code + +# Default Country Code is 2 bytes, 3rd byte is optional indoor or out door. + +# Example + +# US Indoor, USI + +# Korea Outdoor, KRO + +# Japan without optional byte, JP + +# France without optional byte, FR + +#gAPCntryCode=USI + + +#Short Guard Interval Enable/disable + +gShortGI20Mhz=1 + +gShortGI40Mhz=1 + + +#Auto Shutdown Value in seconds. A value of 0 means Auto shutoff is disabled + +gAPAutoShutOff=0 + + +# SAP auto channel selection configuration + +# 0 = disable auto channel selection + +# 1 = enable auto channel selection, channel provided by supplicant will be ignored + +gApAutoChannelSelection=1 +gAPChannelSelectStartChannel=8 +gAPChannelSelectEndChannel=8 +gAPChannelSelectOperatingBand=0 + +#Auto Shutdown wlan : Value in Seconds. 0 means disabled. Max 1 day = 86400 sec +gWlanAutoShutdown = 0 + + +# Listen Energy Detect Mode Configuration + +# Valid values 0-128 + +# 128 means disable Energy Detect feature + +# 0-9 are threshold code and 7 is recommended value from system if feature is to be enabled. + +# 10-128 are reserved. + +# The EDET threshold mapping is as follows in 3dB step: + +# 0 = -60 dBm + +# 1 = -63 dBm + +# 2 = -66 dBm + +# ... + +# 7 = -81 dBm + +# 8 = -84 dBm + +# 9 = -87 dBm + +# Note: Any of these settings are valid. Setting 0 would yield the highest power saving (in a noisy environment) at the cost of more range. The range impact is approximately #calculated as: + +# + +# Range Loss (dB) = EDET threshold level (dBm) + 97 dBm. + +# + +gEnablePhyAgcListenMode=128 + + +#Preferred band (both or 2.4 only or 5 only) + +BandCapability=0 + + +#Beacon Early Termination (1 = enable the BET feature, 0 = disable) + +enableBeaconEarlyTermination=0 + +beaconEarlyTerminationWakeInterval=11 + + +#Channel Bonding +gChannelBondingMode5GHz=1 +gChannelBondingMode24GHz=1 + + +#Enable Keep alive with non-zero period value + +gStaKeepAlivePeriod = 30 + +#If set will start with active scan after driver load, otherwise will start with + +#passive scan to find out the domain + +gEnableBypass11d=1 + + +#If set to 0, will not scan DFS channels + +gEnableDFSChnlScan=1 + + +gVhtChannelWidth=2 + + +gGoKeepAlivePeriod = 30 +gApKeepAlivePeriod = 10 +# Enable Automatic Tx Power control + +gEnableAutomaticTxPowerControl=1 + +# 0 for OLPC 1 for CLPC and SCPC +gEnableCloseLoop=1 + +#Data Inactivity Timeout when in powersave (in ms) +gDataInactivityTimeout=200 + +# VHT Tx/Rx MCS values +# Valid values are 0,1,2. If commented out, the default value is 0. +# 0=MCS0-7, 1=MCS0-8, 2=MCS0-9 +gVhtRxMCS=2 +gVhtTxMCS=2 + +gEnableLpwrImgTransition=1 + +# VHT Tx/Rx MCS values for 2x2 +# Valid values are 0,1,2. If commented out, the default value is 0. +# 0=MCS0-7, 1=MCS0-8, 2=MCS0-9 +#gVhtRxMCS2x2=2 +#gVhtTxMCS2x2=2 + +# Enable Tx beamforming +gTxBFEnable=1 + +# Enable Tx beamforming in VHT20MHz +# Valid values are 0,1. If commented out, the default value is 0. +# 0=disable, 1=enable +gEnableTxBFin20MHz=1 + +gTxChainMask1ss=0 + +# Scan Timing Parameters +# gPassiveMaxChannelTime=110 +# gPassiveMinChannelTime=60 +gActiveMaxChannelTime=40 +gActiveMinChannelTime=20 + +gEnableDynamicDTIM=3 + +#If set to 0, MCC is not allowed. +gEnableMCCMode=1 + +# MCC to SCC Switch mode: 0-Disable 1-Enable 2-Force SCC if same band +gWlanMccToSccSwitchMode = 0 + +# 1=enable STBC; 0=disable STBC +gEnableRXSTBC=1 + +# 1=enable tx STBC; 0=disable +gEnableTXSTBC=1 + +# 1=enable rx LDPC; 0=disable +gEnableRXLDPC=1 + +# Enable Active mode offload +gEnableActiveModeOffload=1 + +#Enable Scan Results Aging based on timer +#Timer value is in seconds +#If Set to 0 it will not enable the feature +gScanAgingTime=0 + +#Enable Scan Results Aging based on number of scans +gScanResultAgeCount=1 + +#Enable Power saving mechanism Based on Android Framework +#If set to 0 Driver internally control the Power saving mechanism +#If set to 1 Android Framwrok control the Power saving mechanism +isAndroidPsEn=0 + +#Enable thermal mitigation +gThermalMitigationEnable=0 + +gEnableFastRoamInConcurrency=1 + +#List of Country codes for which 11ac needs to be disabled +#Each country code must be delimited by comma(,) +gListOfNon11acCountryCode=RU,UA,ZA + +#Maxium Channel time in msec +gMaxMediumTime = 6000 + +# 802.11K support +gRrmEnable=1 +gRrmOperChanMax=8 +gRrmNonOperChanMax=8 +gRrmRandIntvl=100 + +#Scan offload +gEnableDirectedScanOffload=1 + +#FlexConnect Power Factor +#Default is set to 0 (disable) +gFlexConnectPowerFactor=0 + +#Disable split scan, the FW will take care of it +gNumChanCombinedConc=60 + +#Enable Power Save offload +gEnablePowerSaveOffload=1 + +#Enable firmware uart print +gEnablefwprint=0 + +#Enable firmware log +gEnablefwlog=1 +# Additional firmware log levels +gFwDebugLogLevel=1 +gFwDebugModuleLoglevel=1,0,2,0,4,0,5,0,6,0,7,4,8,0,9,0,11,0,13,0,17,0,18,0,19,0,27,0,29,0,31,0,35,0,36,0,38,0 + +#IPA config +gIPADescSize=800 +gIPAPreFilterEnable=1 +gIPARMEnable=1 +gIPAIPv6Enable=1 + +#P2P Listen offload +gEnableP2pListenOffload=1 + +# Maximum Receive AMPDU size (VHT only. Valid values: 0->8k 1->16k 2->32k 3->64k 4->128k) +gVhtAmpduLenExponent=7 + +# Maximum MPDU length (VHT only. Valid values: 0->3895 octets, 1->7991 octets, 2->11454 octets) +gVhtMpduLen=2 + +# Maximum number of wow filters required +#gMaxWoWFilters=22 + +# WOW Enable/Disable. +# 0 - Disable both magic pattern match and pattern byte match. +# 1 - Enable magic pattern match on all interfaces. +# 2 - Enable pattern byte match on all interfaces. +# 3 - Enable both magic patter and pattern byte match on all interfaces. +# Default value of gEnableWoW is 3. +# gEnableWoW=0 + +# Enable or Disable MCC Adaptive Scheduler at the FW +# 1=Enable (default), 0=Disable +gEnableMCCAdaptiveScheduler=1 + +#Enable or Disable p2p device address administered +isP2pDeviceAddrAdministrated=1 + +# RX packet handling options +# 0: no rx thread, no RPS, for MDM +# 1: RX thread +# 2: RPS +rxhandle=2 + +#RPS CPU map, core 2 and 3 +rpsRxQueueCpuMapList=c + +# Set Thermal Power limit +TxPower2g=10 +TxPower5g=10 + +# Remove Overlap channel restriction +gEnableOverLapCh=0 + +#Enable VHT on 2.4Ghz +gEnableVhtFor24GHzBand=1 + +#Enable or Disable 5G early beacon termination +gEnable5gEBT=1 + +#Maximum number of offload peers supported +# gMaxOffloadPeers=2 + +# controlling the following offload patterns +# through ini parameter. Default value is 1 +# to disable set it to zero. ssdp = 0 +# Setup multicast pattern for mDNS 224.0.0.251, +# SSDP 239.255.255.250 and LLMNR 224.0.0.252 + + +ssdp = 0 + +# Bus bandwidth threshold values in terms of number of packets +gBusBandwidthHighThreshold=2000 +gBusBandwidthMediumThreshold=500 +gBusBandwidthLowThreshold=150 + +# IPA bandwidth voting +gIPAHighBandwidthMbps=800 +gIPAMediumBandwidthMbps=400 +gIPALowBandwidthMbps=200 + +# Bus bandwidth compute timeout value in ms +gBusBandwidthComputeInterval=100 + +# Regulatory Setting; 0=STRICT; 1=CUSTOM +gRegulatoryChangeCountry=1 + +# Maximum number of concurrent connections +gMaxConcurrentActiveSessions=2 + +# Radar PRI multiplier +gDFSradarMappingPriMultiplier=4 + +gPNOScanSupport=1 + +# Enable/Disable RX full reorder offload +gReorderOffloadSupported=1 + +# userspace country code setting shld take priority +gCountryCodePriority=1 + +# Enable/Disable LPASS support +# 0 to disable, 1 to enable +gEnableLpassSupport=1 + +# Enable(1)/Disable(0) SIFS burst +gEnableSifsBurst=1 + +# Enable or Disable Multi-user MIMO +# 1=Enable (default), 0=Disable +gEnableMuBformee=1 + +# Enable/Disable channel avoidance for SAP in SCC scenario +# 0 - disable +# 1 - enable +gSapSccChanAvoidance=0 + +# RA filtering rate limit param, the current value would not +# help if the lifetime in RA is less than 3*60=3min. Then +# we need to change it, though it is uncommon. +# gRAFilterEnable=0 +gRArateLimitInterval=60 + +# Inactivity time (in ms) to end TX Service Period while in IBSS power save mode +gIbssTxSpEndInactivityTime=10 + +# Enable support for TDLS +# 0 - disable +# 1 - enable +gEnableTDLSSupport=1 + +# Enable support for Implicit Trigger of TDLS. That is, wlan driver shall +# initiate TDLS Discovery towards a peer whenever setup criteria (throughput +# and RSSI) is met and then will initiate teardown when teardown criteria +# (idle packet count and RSSI) is met. +# 0 - disable +# 1 - enable +gEnableTDLSImplicitTrigger=1 + +# Enable TDLS External Control. That is, user space application has to +# first configure a peer MAC in wlan driver towards which TDLS is desired. +# Device will establish TDLS only towards those configured peers whenever +# TDLS criteria (throughput and RSSI threshold) is met and teardown TDLS +# when teardown criteria (idle packet count and RSSI) is met. However, +# device will accept TDLS connection if it is initiated from any other peer, +# even if that peer is not configured. +# 0 - disable +# 1 - enable +# For TDLS External Control, Implicit Trigger must also be enabled. +gTDLSExternalControl=1 + +# Enable support for TDLS off-channel operation +# 0 - disable +# 1 - enable +# TDLS off-channel operation will be invoked when there is only one +# TDLS connection. +gEnableTDLSOffChannel=1 + +# Enable/Disable Roaming Offload Support (a.k.a Key Management Offload) +# 0 to disable, 1 to enable +gRoamOffloadEnabled=0 + +gEnableSelfRecovery=1 + +#Enable RA filtering offload +gRAFilterEnable=1 + +gAllowDFSChannelRoam=1 + +gChainMask_2g=3 +gChainMask_5g=3 +gVdevTypeNss_2g=43690 +gVdevTypeNss_5g=43690 + +gEnableMemDeepSleep=1 + +gIPAConfig=0x1d +IpaUcOffloadEnabled=1 +gIpaUcStaOffload=0 + +# Enable Runtime PM Feature. +# Enabling this feature will put target wow and shutdown pcie link +# when inactivity is detected in WLAN Driver. +# This feature is inactive when beaconing interfaces are active with +# clients associated. +# 0 - disable +# 1 - enable +gRuntimePM=0 + +# When gRuntimePM is disabled gRuntimeAutoTime won't take effect. +# The Time is in msec. +# 100 is min, 10000 is max, 500 is default. +gRuntimePMDelay=500 + +gEnablePacketLog=0 + +gTxLdpcEnable=3 + +gMulticastHostFwMsgs=0 +#vosTraceEnableWDA=255 +#vosTraceEnableHDD=255 +#vosTraceEnableSME=255 + +END + +# Note: Configuration parser would not read anything past the END marker + |