diff options
| -rw-r--r-- | device.mk | 3 | ||||
| -rw-r--r-- | wifi/WCNSS_cfg.dat | bin | 10234 -> 0 bytes | |||
| -rw-r--r-- | wifi/WCNSS_qcom_cfg.ini | 233 | ||||
| -rw-r--r-- | wifi/p2p_supplicant_overlay.conf | 1 |
4 files changed, 118 insertions, 119 deletions
@@ -263,6 +263,5 @@ PRODUCT_COPY_FILES += \ $(LOCAL_PATH)/wifi/wpa_supplicant_overlay.conf:system/etc/wifi/wpa_supplicant_overlay.conf PRODUCT_COPY_FILES += \ - $(LOCAL_PATH)/wifi/WCNSS_qcom_cfg.ini:system/etc/wifi/WCNSS_qcom_cfg.ini \ - $(LOCAL_PATH)/wifi/WCNSS_cfg.dat:system/etc/firmware/wlan/qca_cld/WCNSS_cfg.dat + $(LOCAL_PATH)/wifi/WCNSS_qcom_cfg.ini:system/etc/wifi/WCNSS_qcom_cfg.ini diff --git a/wifi/WCNSS_cfg.dat b/wifi/WCNSS_cfg.dat Binary files differdeleted file mode 100644 index 08aaf2b..0000000 --- a/wifi/WCNSS_cfg.dat +++ /dev/null diff --git a/wifi/WCNSS_qcom_cfg.ini b/wifi/WCNSS_qcom_cfg.ini index 643de96..b645922 100644 --- a/wifi/WCNSS_qcom_cfg.ini +++ b/wifi/WCNSS_qcom_cfg.ini @@ -2,6 +2,22 @@ # defaults for the WLAN Driver +gInitialScanNoDFSChnl=1 +gInitialDwellTime=20 +RoamRssiDiff=5 +gEnable2x2=0 +g11dSupportEnabled=1 +gSoftApMaxPeers=8 +gRAFilterEnable=0 +gRoamBmissFirstBcnt=25 +gRoamBmissFinalBcnt=35 +RTSThreshold=117350 +gTcpDelAckThresholdHigh=10000 +gDroppedPktDisconnectTh=1024 +gRuntimePM=0 +gMCAddrListEnable=0 +gBpfFilterEnable=0 +gEnablePowerSaveOffload=1 # Enable IMPS or not gEnableImps=1 @@ -75,7 +91,7 @@ gNthBeaconFilter=50 # Enable WAPI or not -WAPIIsEnabled=1 +# WAPIIsEnabled=0 # Flags to filter Mcast abd Bcast RX packets. @@ -129,22 +145,6 @@ gEnableApUapsd=1 gFixedRate=0 - -# Maximum Tx power - -# gTxPowerCap=30 - - -# Fragmentation Threshold - -# gFragmentationThreshold=2346 - - -# RTS threshold - -RTSThreshold=1048576 - - # Intra-BSS forward gDisableIntraBssFwd=0 @@ -154,11 +154,6 @@ gDisableIntraBssFwd=0 WmmIsEnabled=0 - -# 802.11d support - -g11dSupportEnabled=1 - # 802.11h support g11hSupportEnabled=1 @@ -167,7 +162,7 @@ g11hSupportEnabled=1 gEnableDFSMasterCap=1 # ESE Support and fast transition -EseEnabled=0 +EseEnabled=1 ImplicitQosIsEnabled=0 gNeighborScanTimerPeriod=200 @@ -183,11 +178,6 @@ gMaxNeighborReqTries=3 # To disable, set FastRoamEnabled=0 FastRoamEnabled=1 -#Check if the AP to which we are roaming is better than current AP in terms of RSSI. -#Checking is disabled if set to Zero.Otherwise it will use this value as to how better -#the RSSI of the new/roamable AP should be for roaming -RoamRssiDiff=5 - # If the RSSI of any available candidate is better than currently associated # AP by at least gImmediateRoamRssiDiff, then being to roam immediately (without # registering for reassoc threshold). @@ -198,22 +188,6 @@ gImmediateRoamRssiDiff=10 # To disable, set gRoamIntraBand=0 (Roaming across band) gRoamIntraBand=0 -# SAP Country code - -# Default Country Code is 2 bytes, 3rd byte is optional indoor or out door. - -# Example - -# US Indoor, USI - -# Korea Outdoor, KRO - -# Japan without optional byte, JP - -# France without optional byte, FR - -#gAPCntryCode=USI - #Short Guard Interval Enable/disable @@ -226,6 +200,9 @@ gShortGI40Mhz=1 gAPAutoShutOff=0 +#Auto Shutdown wlan : Value in Seconds. 0 means disabled. Max 1 day = 86400 sec +gWlanAutoShutdown = 0 + # SAP auto channel selection configuration @@ -233,13 +210,7 @@ gAPAutoShutOff=0 # 1 = enable auto channel selection, channel provided by supplicant will be ignored -gApAutoChannelSelection=1 -gAPChannelSelectStartChannel=8 -gAPChannelSelectEndChannel=8 -gAPChannelSelectOperatingBand=0 - -#Auto Shutdown wlan : Value in Seconds. 0 means disabled. Max 1 day = 86400 sec -gWlanAutoShutdown = 0 +gApAutoChannelSelection=0 # Listen Energy Detect Mode Configuration @@ -286,19 +257,52 @@ BandCapability=0 #Beacon Early Termination (1 = enable the BET feature, 0 = disable) -enableBeaconEarlyTermination=1 +enableBeaconEarlyTermination=0 + +beaconEarlyTerminationWakeInterval=3 -beaconEarlyTerminationWakeInterval=8 + +#SOFTAP Channel Range selection + +gAPChannelSelectStartChannel=1 + +gAPChannelSelectEndChannel=11 + + +#SOFTAP Channel Range selection Operating band + +# 0:2.4GHZ 1: LOW-5GHZ 2:MID-5GHZ 3:HIGH-5GHZ 4: 4.9HZ BAND + +gAPChannelSelectOperatingBand=0 #Channel Bonding gChannelBondingMode5GHz=1 -gChannelBondingMode24GHz=1 +gChannelBondingMode24GHz=0 #Enable Keep alive with non-zero period value -gStaKeepAlivePeriod = 10 +gStaKeepAlivePeriod = 30 + +#Say gGoKeepAlivePeriod(5 seconds) and gGoLinkMonitorPeriod(10 seconds). +#For every 10 seconds DUT send Qos Null frame(i.e., Keep Alive frame if link is idle for last 10 seconds.) +#For both active and power save clients. + +#Power save clients: DUT set TIM bit from 10th second onwards and till client honors TIM bit. +#If doesn't honor for 5 seconds then DUT remove client. + +#Active clients: DUT send Qos Null frame for 10th seconds onwards if it is not success still we try on +#11th second if not tries on 12th and so on till 15th second. Hence before disconnection DUT will send 5 NULL frames. +#Hence in any case DUT will detect client got removed in (10+5) seconds. i.e., (gGoKeepAlivePeriod + gGoLinkMonitorPeriod).. + +#gGoLinkMonitorPeriod/ gApLinkMonitorPeriod is period where link is idle and it is period +#where we send NULL frame. + +#gApLinkMonitorPeriod = 10 + +#gGoLinkMonitorPeriod = 10 + #If set will start with active scan after driver load, otherwise will start with @@ -313,10 +317,9 @@ gEnableDFSChnlScan=1 gVhtChannelWidth=2 +gEnableLogp=1 -gGoKeepAlivePeriod = 30 -gApKeepAlivePeriod = 10 # Enable Automatic Tx Power control gEnableAutomaticTxPowerControl=1 @@ -333,13 +336,11 @@ gDataInactivityTimeout=200 gVhtRxMCS=2 gVhtTxMCS=2 -gEnableLpwrImgTransition=1 - # VHT Tx/Rx MCS values for 2x2 # Valid values are 0,1,2. If commented out, the default value is 0. # 0=MCS0-7, 1=MCS0-8, 2=MCS0-9 -#gVhtRxMCS2x2=2 -#gVhtTxMCS2x2=2 +gVhtRxMCS2x2=2 +gVhtTxMCS2x2=2 # Enable Tx beamforming gTxBFEnable=1 @@ -349,7 +350,13 @@ gTxBFEnable=1 # 0=disable, 1=enable gEnableTxBFin20MHz=1 -gTxChainMask1ss=0 +# Set txchainmask and rxchainmask +# These parameters are used only if gEnable2x2 is 0 +# Valid values are 1,2 +# Set gSetTxChainmask1x1=1 or gSetRxChainmask1x1=1 to select chain0. +# Set gSetTxChainmask1x1=2 or gSetRxChainmask1x1=2 to select chain1. +gSetTxChainmask1x1=1 +gSetRxChainmask1x1=1 # Scan Timing Parameters # gPassiveMaxChannelTime=110 @@ -357,8 +364,6 @@ gTxChainMask1ss=0 gActiveMaxChannelTime=40 gActiveMinChannelTime=20 -gEnableDynamicDTIM=3 - #If set to 0, MCC is not allowed. gEnableMCCMode=1 @@ -374,6 +379,10 @@ gEnableTXSTBC=1 # 1=enable rx LDPC; 0=disable gEnableRXLDPC=1 +# Enable or Disable txLdpc capability +# 0 - disable, 1 - HT LDPC enable, 2 - VHT LDPC enable, 3 - HT & VHT LDPC enable +gTxLdpcEnable=3 + # Enable Active mode offload gEnableActiveModeOffload=1 @@ -395,10 +404,6 @@ gThermalMitigationEnable=0 gEnableFastRoamInConcurrency=1 -#List of Country codes for which 11ac needs to be disabled -#Each country code must be delimited by comma(,) -gListOfNon11acCountryCode=RU,UA,ZA - #Maxium Channel time in msec gMaxMediumTime = 6000 @@ -418,23 +423,27 @@ gFlexConnectPowerFactor=0 #Disable split scan, the FW will take care of it gNumChanCombinedConc=60 -#Enable Power Save offload -gEnablePowerSaveOffload=4 - #Enable firmware uart print gEnablefwprint=0 #Enable firmware log gEnablefwlog=1 # Additional firmware log levels -gFwDebugLogLevel=1 +gFwDebugLogLevel=4 gFwDebugModuleLoglevel=1,0,2,0,4,0,5,0,6,0,7,4,8,0,9,0,11,0,13,0,17,0,18,0,19,0,27,0,29,0,31,0,35,0,36,0,38,0 #IPA config +#gIPAEnable=0x00 gIPADescSize=800 gIPAPreFilterEnable=1 gIPARMEnable=1 gIPAIPv6Enable=1 +gIPAConfig=0x1d +IpaUcOffloadEnabled=1 +gIpaUcStaOffload=0 +gIPAHighBandwidthMbps=800 +gIPAMediumBandwidthMbps=400 +gIPALowBandwidthMbps=200 #P2P Listen offload gEnableP2pListenOffload=1 @@ -469,13 +478,6 @@ isP2pDeviceAddrAdministrated=1 # 2: RPS rxhandle=2 -#RPS CPU map, core 2 and 3 -rpsRxQueueCpuMapList=c - -# Set Thermal Power limit -TxPower2g=10 -TxPower5g=10 - # Remove Overlap channel restriction gEnableOverLapCh=0 @@ -497,16 +499,12 @@ gEnable5gEBT=1 ssdp = 0 + # Bus bandwidth threshold values in terms of number of packets gBusBandwidthHighThreshold=2000 gBusBandwidthMediumThreshold=500 gBusBandwidthLowThreshold=150 -# IPA bandwidth voting -gIPAHighBandwidthMbps=800 -gIPAMediumBandwidthMbps=400 -gIPALowBandwidthMbps=200 - # Bus bandwidth compute timeout value in ms gBusBandwidthComputeInterval=100 @@ -521,6 +519,14 @@ gDFSradarMappingPriMultiplier=4 gPNOScanSupport=1 +# Perform PNO fast scan this many number of times +gPNOScanTimerRepeatValue=6 + +# PNO slow scan period = gPNOSlowScanMultiplier times PNO fast scan period +# Example: fast scan period is passed from framework (default = 10 sec), then +# PNO slow scan period = 60 sec. +gPNOSlowScanMultiplier=6 + # Enable/Disable RX full reorder offload gReorderOffloadSupported=1 @@ -546,8 +552,8 @@ gSapSccChanAvoidance=0 # RA filtering rate limit param, the current value would not # help if the lifetime in RA is less than 3*60=3min. Then # we need to change it, though it is uncommon. -# gRAFilterEnable=0 -gRArateLimitInterval=60 +# Enable RA filtering offload +gRArateLimitInterval=300 # Inactivity time (in ms) to end TX Service Period while in IBSS power save mode gIbssTxSpEndInactivityTime=10 @@ -584,53 +590,46 @@ gTDLSExternalControl=1 # TDLS connection. gEnableTDLSOffChannel=1 +gEnableTDLSScan=1 +gTDLSTxStatsPeriod=500 +gTDLSTxPacketThreshold=10 +gTDLSIdlePacketThreshold=1 + # Enable/Disable Roaming Offload Support (a.k.a Key Management Offload) # 0 to disable, 1 to enable gRoamOffloadEnabled=0 gEnableSelfRecovery=1 -#Enable RA filtering offload -gRAFilterEnable=1 - -gAllowDFSChannelRoam=1 +# When gRuntimePM is disabled gRuntimeAutoTime won't take effect. +# The Time is in msec. +# 100 is min, 10000 is max, 500 is default. -gChainMask_2g=3 -gChainMask_5g=3 -gVdevTypeNss_2g=43690 -gVdevTypeNss_5g=43690 +gRuntimePMDelay=500 -gEnableMemDeepSleep=1 +# Enable to check FW hash if secure FW feature is enabled. It's for defconfig +# builds only since it will be ignored in performance/release builds. +gEnableFWHashCheck=1 -gIPAConfig=0x1d -IpaUcOffloadEnabled=1 -gIpaUcStaOffload=0 +# Tx Chain Mask for CCK +gCckChainMaskEnable=1 -# Enable Runtime PM Feature. -# Enabling this feature will put target wow and shutdown pcie link -# when inactivity is detected in WLAN Driver. -# This feature is inactive when beaconing interfaces are active with -# clients associated. -# 0 - disable -# 1 - enable -gRuntimePM=0 +# Tx Chain Mask for 1SS +gTxChainMask1ss=0 -# When gRuntimePM is disabled gRuntimeAutoTime won't take effect. -# The Time is in msec. -# 100 is min, 10000 is max, 500 is default. +# TPC power +gSelfGenFrmPwr=3 -gRuntimePMDelay=1500 +gAllowDFSChannelRoam=1 -gEnablePacketLog=0 +# Enable or Disable Extended Scan (GScan) +# 1=Enable (default), 0=Disable +gExtScanEnable=1 -gTxLdpcEnable=3 -gMulticastHostFwMsgs=0 -#vosTraceEnableWDA=255 -#vosTraceEnableHDD=255 -#vosTraceEnableSME=255 +gEnableModulatedDTIM=2 +gMaxLIModulatedDTIM=6 END # Note: Configuration parser would not read anything past the END marker - diff --git a/wifi/p2p_supplicant_overlay.conf b/wifi/p2p_supplicant_overlay.conf index b5e89e0..71f2e4f 100644 --- a/wifi/p2p_supplicant_overlay.conf +++ b/wifi/p2p_supplicant_overlay.conf @@ -1,2 +1,3 @@ disable_scan_offload=1 +p2p_search_delay=100 p2p_no_group_iface=1 |