From ec38846ad59d7b780540afcec101b24139933195 Mon Sep 17 00:00:00 2001 From: Alexandre Belloni Date: Thu, 29 May 2014 01:20:16 +0200 Subject: backlight: atmel-pwm-bl: remove obsolete driver The atmel-pwm-bl driver is now obsolete. It is not used by any mainlined boards and is replaced by the generic pwm_bl with the pawm-atmel driver using the generic PWM framework. Signed-off-by: Alexandre Belloni Acked-by: Hans-Christian Egtvedt Acked-by: Jingoo Han Signed-off-by: Nicolas Ferre --- include/linux/atmel-pwm-bl.h | 43 ------------------------------------------- 1 file changed, 43 deletions(-) delete mode 100644 include/linux/atmel-pwm-bl.h (limited to 'include') diff --git a/include/linux/atmel-pwm-bl.h b/include/linux/atmel-pwm-bl.h deleted file mode 100644 index 0153a47806c2..000000000000 --- a/include/linux/atmel-pwm-bl.h +++ /dev/null @@ -1,43 +0,0 @@ -/* - * Copyright (C) 2007 Atmel Corporation - * - * Driver for the AT32AP700X PS/2 controller (PSIF). - * - * This program is free software; you can redistribute it and/or modify it - * under the terms of the GNU General Public License version 2 as published - * by the Free Software Foundation. - */ - -#ifndef __INCLUDE_ATMEL_PWM_BL_H -#define __INCLUDE_ATMEL_PWM_BL_H - -/** - * struct atmel_pwm_bl_platform_data - * @pwm_channel: which PWM channel in the PWM module to use. - * @pwm_frequency: PWM frequency to generate, the driver will try to be as - * close as the prescaler allows. - * @pwm_compare_max: value to use in the PWM channel compare register. - * @pwm_duty_max: maximum duty cycle value, must be less than or equal to - * pwm_compare_max. - * @pwm_duty_min: minimum duty cycle value, must be less than pwm_duty_max. - * @pwm_active_low: set to one if the low part of the PWM signal increases the - * brightness of the backlight. - * @gpio_on: GPIO line to control the backlight on/off, set to -1 if not used. - * @on_active_low: set to one if the on/off signal is on when GPIO is low. - * - * This struct must be added to the platform device in the board code. It is - * used by the atmel-pwm-bl driver to setup the GPIO to control on/off and the - * PWM device. - */ -struct atmel_pwm_bl_platform_data { - unsigned int pwm_channel; - unsigned int pwm_frequency; - unsigned int pwm_compare_max; - unsigned int pwm_duty_max; - unsigned int pwm_duty_min; - unsigned int pwm_active_low; - int gpio_on; - unsigned int on_active_low; -}; - -#endif /* __INCLUDE_ATMEL_PWM_BL_H */ -- cgit v1.2.3 From f2a70e1fc1ccc0fcdf4ad12db7382134228fb552 Mon Sep 17 00:00:00 2001 From: Alexandre Belloni Date: Thu, 29 May 2014 01:20:18 +0200 Subject: misc: atmel_pwm: remove obsolete driver The misc/atmel_pwm is not used by any mainlined boards and has been replaced by the pwm-driver using the generic PWM framework. Signed-off-by: Alexandre Belloni Acked-by: Greg Kroah-Hartman Signed-off-by: Nicolas Ferre --- include/linux/atmel_pwm.h | 70 ----------------------------------------------- 1 file changed, 70 deletions(-) delete mode 100644 include/linux/atmel_pwm.h (limited to 'include') diff --git a/include/linux/atmel_pwm.h b/include/linux/atmel_pwm.h deleted file mode 100644 index ea04abb3db8e..000000000000 --- a/include/linux/atmel_pwm.h +++ /dev/null @@ -1,70 +0,0 @@ -#ifndef __LINUX_ATMEL_PWM_H -#define __LINUX_ATMEL_PWM_H - -/** - * struct pwm_channel - driver handle to a PWM channel - * @regs: base of this channel's registers - * @index: number of this channel (0..31) - * @mck: base clock rate, which can be prescaled and maybe subdivided - * - * Drivers initialize a pwm_channel structure using pwm_channel_alloc(). - * Then they configure its clock rate (derived from MCK), alignment, - * polarity, and duty cycle by writing directly to the channel registers, - * before enabling the channel by calling pwm_channel_enable(). - * - * After emitting a PWM signal for the desired length of time, drivers - * may then pwm_channel_disable() or pwm_channel_free(). Both of these - * disable the channel, but when it's freed the IRQ is deconfigured and - * the channel must later be re-allocated and reconfigured. - * - * Note that if the period or duty cycle need to be changed while the - * PWM channel is operating, drivers must use the PWM_CUPD double buffer - * mechanism, either polling until they change or getting implicitly - * notified through a once-per-period interrupt handler. - */ -struct pwm_channel { - void __iomem *regs; - unsigned index; - unsigned long mck; -}; - -extern int pwm_channel_alloc(int index, struct pwm_channel *ch); -extern int pwm_channel_free(struct pwm_channel *ch); - -extern int pwm_clk_alloc(unsigned prescale, unsigned div); -extern void pwm_clk_free(unsigned clk); - -extern int __pwm_channel_onoff(struct pwm_channel *ch, int enabled); - -#define pwm_channel_enable(ch) __pwm_channel_onoff((ch), 1) -#define pwm_channel_disable(ch) __pwm_channel_onoff((ch), 0) - -/* periodic interrupts, mostly for CUPD changes to period or cycle */ -extern int pwm_channel_handler(struct pwm_channel *ch, - void (*handler)(struct pwm_channel *ch)); - -/* per-channel registers (banked at pwm_channel->regs) */ -#define PWM_CMR 0x00 /* mode register */ -#define PWM_CPR_CPD (1 << 10) /* set: CUPD modifies period */ -#define PWM_CPR_CPOL (1 << 9) /* set: idle high */ -#define PWM_CPR_CALG (1 << 8) /* set: center align */ -#define PWM_CPR_CPRE (0xf << 0) /* mask: rate is mck/(2^pre) */ -#define PWM_CPR_CLKA (0xb << 0) /* rate CLKA */ -#define PWM_CPR_CLKB (0xc << 0) /* rate CLKB */ -#define PWM_CDTY 0x04 /* duty cycle (max of CPRD) */ -#define PWM_CPRD 0x08 /* period (count up from zero) */ -#define PWM_CCNT 0x0c /* counter (20 bits?) */ -#define PWM_CUPD 0x10 /* update CPRD (or CDTY) next period */ - -static inline void -pwm_channel_writel(struct pwm_channel *pwmc, unsigned offset, u32 val) -{ - __raw_writel(val, pwmc->regs + offset); -} - -static inline u32 pwm_channel_readl(struct pwm_channel *pwmc, unsigned offset) -{ - return __raw_readl(pwmc->regs + offset); -} - -#endif /* __LINUX_ATMEL_PWM_H */ -- cgit v1.2.3