From d582cffbcd04eae0bd8a83b05648bfd54bfd21c9 Mon Sep 17 00:00:00 2001 From: Johannes Berg Date: Fri, 26 Oct 2012 17:53:44 +0200 Subject: nl80211/mac80211: support full station state in AP mode Today, stations are added already associated. That is inefficient if, for example, the driver has no room for stations any more because then the station will go through the entire auth/assoc handshake, only to be kicked out afterwards. To address this a bit better, at least with drivers using the new station state callback, allow hostapd to add stations in unauthenticated mode, just after receiving the AUTH frame, before even replying. Thus if there's no more space at that point, it can send a negative auth frame back. It still needs to handle later state transition errors though, of course. Signed-off-by: Johannes Berg --- include/uapi/linux/nl80211.h | 16 ++++++++++++++++ 1 file changed, 16 insertions(+) (limited to 'include/uapi/linux') diff --git a/include/uapi/linux/nl80211.h b/include/uapi/linux/nl80211.h index e3e19f8b16f2..547017100a30 100644 --- a/include/uapi/linux/nl80211.h +++ b/include/uapi/linux/nl80211.h @@ -1697,6 +1697,9 @@ enum nl80211_iftype { * flag can't be changed, it is only valid while adding a station, and * attempts to change it will silently be ignored (rather than rejected * as errors.) + * @NL80211_STA_FLAG_ASSOCIATED: station is associated; used with drivers + * that support %NL80211_FEATURE_FULL_AP_CLIENT_STATE to transition a + * previously added station into associated state * @NL80211_STA_FLAG_MAX: highest station flag number currently defined * @__NL80211_STA_FLAG_AFTER_LAST: internal use */ @@ -1708,6 +1711,7 @@ enum nl80211_sta_flags { NL80211_STA_FLAG_MFP, NL80211_STA_FLAG_AUTHENTICATED, NL80211_STA_FLAG_TDLS_PEER, + NL80211_STA_FLAG_ASSOCIATED, /* keep last */ __NL80211_STA_FLAG_AFTER_LAST, @@ -3140,6 +3144,17 @@ enum nl80211_ap_sme_features { * setting * @NL80211_FEATURE_P2P_GO_OPPPS: P2P GO implementation supports opportunistic * powersave + * @NL80211_FEATURE_FULL_AP_CLIENT_STATE: The driver supports full state + * transitions for AP clients. Without this flag (and if the driver + * doesn't have the AP SME in the device) the driver supports adding + * stations only when they're associated and adds them in associated + * state (to later be transitioned into authorized), with this flag + * they should be added before even sending the authentication reply + * and then transitioned into authenticated, associated and authorized + * states using station flags. + * Note that even for drivers that support this, the default is to add + * stations in authenticated/associated state, so to add unauthenticated + * stations the authenticated/associated bits have to be set in the mask. */ enum nl80211_feature_flags { NL80211_FEATURE_SK_TX_STATUS = 1 << 0, @@ -3155,6 +3170,7 @@ enum nl80211_feature_flags { NL80211_FEATURE_NEED_OBSS_SCAN = 1 << 10, NL80211_FEATURE_P2P_GO_CTWIN = 1 << 11, NL80211_FEATURE_P2P_GO_OPPPS = 1 << 12, + NL80211_FEATURE_FULL_AP_CLIENT_STATE = 1 << 13, }; /** -- cgit v1.2.3 From 390a1bd8538132186ddb679cafe9e75b7ef7e2d2 Mon Sep 17 00:00:00 2001 From: Samuel Ortiz Date: Wed, 19 Dec 2012 19:11:32 +0100 Subject: NFC: Initial Secure Element API Each NFC adapter can have several links to different secure elements and that property needs to be exported by the drivers. A secure element link can be enabled and disabled, and card emulation will be handled by the currently active one. Otherwise card emulation will be host implemented. Signed-off-by: Samuel Ortiz --- include/uapi/linux/nfc.h | 14 ++++++++++++++ 1 file changed, 14 insertions(+) (limited to 'include/uapi/linux') diff --git a/include/uapi/linux/nfc.h b/include/uapi/linux/nfc.h index 0e63cee8d810..80e4ecd8c04c 100644 --- a/include/uapi/linux/nfc.h +++ b/include/uapi/linux/nfc.h @@ -67,6 +67,11 @@ * subsequent CONNECT and CC messages. * If one of the passed parameters is wrong none is set and -EINVAL is * returned. + * @NFC_CMD_ENABLE_SE: Enable the physical link to a specific secure element. + * Once enabled a secure element will handle card emulation mode, i.e. + * starting a poll from a device which has a secure element enabled means + * we want to do SE based card emulation. + * @NFC_CMD_DISABLE_SE: Disable the physical link to a specific secure element. */ enum nfc_commands { NFC_CMD_UNSPEC, @@ -86,6 +91,8 @@ enum nfc_commands { NFC_EVENT_TM_DEACTIVATED, NFC_CMD_LLC_GET_PARAMS, NFC_CMD_LLC_SET_PARAMS, + NFC_CMD_ENABLE_SE, + NFC_CMD_DISABLE_SE, /* private: internal use only */ __NFC_CMD_AFTER_LAST }; @@ -114,6 +121,7 @@ enum nfc_commands { * @NFC_ATTR_LLC_PARAM_LTO: Link TimeOut parameter * @NFC_ATTR_LLC_PARAM_RW: Receive Window size parameter * @NFC_ATTR_LLC_PARAM_MIUX: MIU eXtension parameter + * @NFC_ATTR_SE: Available Secure Elements */ enum nfc_attrs { NFC_ATTR_UNSPEC, @@ -134,6 +142,7 @@ enum nfc_attrs { NFC_ATTR_LLC_PARAM_LTO, NFC_ATTR_LLC_PARAM_RW, NFC_ATTR_LLC_PARAM_MIUX, + NFC_ATTR_SE, /* private: internal use only */ __NFC_ATTR_AFTER_LAST }; @@ -172,6 +181,11 @@ enum nfc_attrs { #define NFC_PROTO_NFC_DEP_MASK (1 << NFC_PROTO_NFC_DEP) #define NFC_PROTO_ISO14443_B_MASK (1 << NFC_PROTO_ISO14443_B) +/* NFC Secure Elements */ +#define NFC_SE_NONE 0x0 +#define NFC_SE_UICC 0x1 +#define NFC_SE_EMBEDDED 0x2 + struct sockaddr_nfc { sa_family_t sa_family; __u32 dev_idx; -- cgit v1.2.3 From d3710e74cf329839dea8d13b1ad56e572b06b173 Mon Sep 17 00:00:00 2001 From: Lauro Ramos Venancio Date: Wed, 5 Dec 2012 21:12:25 -0300 Subject: NFC: Change nfc.h license nfc.h being GPL makes it quite controversial for non GPL applications to include it. Moreover, nfc.h only includes structures and API definitions that are hardly copyrightable. Signed-off-by: Lauro Ramos Venancio Signed-off-by: Samuel Ortiz --- include/uapi/linux/nfc.h | 23 ++++++++++------------- 1 file changed, 10 insertions(+), 13 deletions(-) (limited to 'include/uapi/linux') diff --git a/include/uapi/linux/nfc.h b/include/uapi/linux/nfc.h index 80e4ecd8c04c..7969f46f1bb3 100644 --- a/include/uapi/linux/nfc.h +++ b/include/uapi/linux/nfc.h @@ -5,20 +5,17 @@ * Lauro Ramos Venancio * Aloisio Almeida Jr * - * This program is free software; you can redistribute it and/or modify - * it under the terms of the GNU General Public License as published by - * the Free Software Foundation; either version 2 of the License, or - * (at your option) any later version. + * Permission to use, copy, modify, and/or distribute this software for any + * purpose with or without fee is hereby granted, provided that the above + * copyright notice and this permission notice appear in all copies. * - * This program is distributed in the hope that it will be useful, - * but WITHOUT ANY WARRANTY; without even the implied warranty of - * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the - * GNU General Public License for more details. - * - * You should have received a copy of the GNU General Public License - * along with this program; if not, write to the - * Free Software Foundation, Inc., - * 59 Temple Place - Suite 330, Boston, MA 02111-1307, USA. + * THE SOFTWARE IS PROVIDED "AS IS" AND THE AUTHOR DISCLAIMS ALL WARRANTIES + * WITH REGARD TO THIS SOFTWARE INCLUDING ALL IMPLIED WARRANTIES OF + * MERCHANTABILITY AND FITNESS. IN NO EVENT SHALL THE AUTHOR BE LIABLE FOR + * ANY SPECIAL, DIRECT, INDIRECT, OR CONSEQUENTIAL DAMAGES OR ANY DAMAGES + * WHATSOEVER RESULTING FROM LOSS OF USE, DATA OR PROFITS, WHETHER IN AN + * ACTION OF CONTRACT, NEGLIGENCE OR OTHER TORTIOUS ACTION, ARISING OUT OF + * OR IN CONNECTION WITH THE USE OR PERFORMANCE OF THIS SOFTWARE. */ #ifndef __LINUX_NFC_H -- cgit v1.2.3 From 3b1c5a5307fb5277f395efdcf330c064d79df07d Mon Sep 17 00:00:00 2001 From: Marco Porsch Date: Mon, 7 Jan 2013 16:04:52 +0100 Subject: {cfg,nl}80211: mesh power mode primitives and userspace access Add the nl80211_mesh_power_mode enumeration which holds possible values for the mesh power mode. These modes are unknown, active, light sleep and deep sleep. Add power_mode entry to the mesh config structure to hold the user-configured default mesh power mode. This value will be used for new peer links. Add the dot11MeshAwakeWindowDuration value to the mesh config. The awake window is a duration in TU describing how long the STA will stay awake after transmitting its beacon in PS mode. Add access routines to: - get/set local link-specific power mode (STA) - get remote STA's link-specific power mode (STA) - get remote STA's non-peer power mode (STA) - get/set default mesh power mode (mesh config) - get/set mesh awake window duration (mesh config) All config changes may be done at mesh runtime and take effect immediately. Signed-off-by: Marco Porsch Signed-off-by: Ivan Bezyazychnyy Signed-off-by: Mike Krinkin [fix commit message line length, error handling in set station] Signed-off-by: Johannes Berg --- include/uapi/linux/nl80211.h | 47 ++++++++++++++++++++++++++++++++++++++++++++ 1 file changed, 47 insertions(+) (limited to 'include/uapi/linux') diff --git a/include/uapi/linux/nl80211.h b/include/uapi/linux/nl80211.h index 547017100a30..6c4f703ae890 100644 --- a/include/uapi/linux/nl80211.h +++ b/include/uapi/linux/nl80211.h @@ -1310,6 +1310,9 @@ enum nl80211_commands { * if not given in START_AP 0 is assumed, if not given in SET_BSS * no change is made. * + * @NL80211_ATTR_LOCAL_MESH_POWER_MODE: local mesh STA link-specific power mode + * defined in &enum nl80211_mesh_power_mode. + * * @NL80211_ATTR_MAX: highest attribute number currently defined * @__NL80211_ATTR_AFTER_LAST: internal use */ @@ -1580,6 +1583,8 @@ enum nl80211_attrs { NL80211_ATTR_P2P_CTWINDOW, NL80211_ATTR_P2P_OPPPS, + NL80211_ATTR_LOCAL_MESH_POWER_MODE, + /* add attributes here, update the policy in nl80211.c */ __NL80211_ATTR_AFTER_LAST, @@ -1838,6 +1843,10 @@ enum nl80211_sta_bss_param { * @NL80211_STA_INFO_STA_FLAGS: Contains a struct nl80211_sta_flag_update. * @NL80211_STA_INFO_BEACON_LOSS: count of times beacon loss was detected (u32) * @NL80211_STA_INFO_T_OFFSET: timing offset with respect to this STA (s64) + * @NL80211_STA_INFO_LOCAL_PM: local mesh STA link-specific power mode + * @NL80211_STA_INFO_PEER_PM: peer mesh STA link-specific power mode + * @NL80211_STA_INFO_NONPEER_PM: neighbor mesh STA power save mode towards + * non-peer STA * @__NL80211_STA_INFO_AFTER_LAST: internal * @NL80211_STA_INFO_MAX: highest possible station info attribute */ @@ -1862,6 +1871,9 @@ enum nl80211_sta_info { NL80211_STA_INFO_STA_FLAGS, NL80211_STA_INFO_BEACON_LOSS, NL80211_STA_INFO_T_OFFSET, + NL80211_STA_INFO_LOCAL_PM, + NL80211_STA_INFO_PEER_PM, + NL80211_STA_INFO_NONPEER_PM, /* keep last */ __NL80211_STA_INFO_AFTER_LAST, @@ -2252,6 +2264,34 @@ enum nl80211_mntr_flags { NL80211_MNTR_FLAG_MAX = __NL80211_MNTR_FLAG_AFTER_LAST - 1 }; +/** + * enum nl80211_mesh_power_mode - mesh power save modes + * + * @NL80211_MESH_POWER_UNKNOWN: The mesh power mode of the mesh STA is + * not known or has not been set yet. + * @NL80211_MESH_POWER_ACTIVE: Active mesh power mode. The mesh STA is + * in Awake state all the time. + * @NL80211_MESH_POWER_LIGHT_SLEEP: Light sleep mode. The mesh STA will + * alternate between Active and Doze states, but will wake up for + * neighbor's beacons. + * @NL80211_MESH_POWER_DEEP_SLEEP: Deep sleep mode. The mesh STA will + * alternate between Active and Doze states, but may not wake up + * for neighbor's beacons. + * + * @__NL80211_MESH_POWER_AFTER_LAST - internal use + * @NL80211_MESH_POWER_MAX - highest possible power save level + */ + +enum nl80211_mesh_power_mode { + NL80211_MESH_POWER_UNKNOWN, + NL80211_MESH_POWER_ACTIVE, + NL80211_MESH_POWER_LIGHT_SLEEP, + NL80211_MESH_POWER_DEEP_SLEEP, + + __NL80211_MESH_POWER_AFTER_LAST, + NL80211_MESH_POWER_MAX = __NL80211_MESH_POWER_AFTER_LAST - 1 +}; + /** * enum nl80211_meshconf_params - mesh configuration parameters * @@ -2346,6 +2386,11 @@ enum nl80211_mntr_flags { * (in TUs) during which a mesh STA can send only one Action frame * containing a PREQ element for root path confirmation. * + * @NL80211_MESHCONF_POWER_MODE: Default mesh power mode for new peer links. + * type &enum nl80211_mesh_power_mode (u32) + * + * @NL80211_MESHCONF_AWAKE_WINDOW: awake window duration (in TUs) + * * @__NL80211_MESHCONF_ATTR_AFTER_LAST: internal use */ enum nl80211_meshconf_params { @@ -2375,6 +2420,8 @@ enum nl80211_meshconf_params { NL80211_MESHCONF_HWMP_PATH_TO_ROOT_TIMEOUT, NL80211_MESHCONF_HWMP_ROOT_INTERVAL, NL80211_MESHCONF_HWMP_CONFIRMATION_INTERVAL, + NL80211_MESHCONF_POWER_MODE, + NL80211_MESHCONF_AWAKE_WINDOW, /* keep last */ __NL80211_MESHCONF_ATTR_AFTER_LAST, -- cgit v1.2.3 From cee00a959c0a86571e6f99cf42f0261d7e54d2ae Mon Sep 17 00:00:00 2001 From: Jouni Malinen Date: Tue, 15 Jan 2013 17:15:57 +0200 Subject: cfg80211: Allow use_mfp to be specified with the connect command The NL80211_ATTR_USE_MFP attribute was originally added for NL80211_CMD_ASSOCIATE, but it is actually as useful (if not even more useful) with NL80211_CMD_CONNECT, so process that attribute with the connect command, too. Signed-off-by: Jouni Malinen Signed-off-by: Johannes Berg --- include/uapi/linux/nl80211.h | 6 +++--- 1 file changed, 3 insertions(+), 3 deletions(-) (limited to 'include/uapi/linux') diff --git a/include/uapi/linux/nl80211.h b/include/uapi/linux/nl80211.h index 6c4f703ae890..d01c16220dc5 100644 --- a/include/uapi/linux/nl80211.h +++ b/include/uapi/linux/nl80211.h @@ -374,8 +374,8 @@ * requests to connect to a specified network but without separating * auth and assoc steps. For this, you need to specify the SSID in a * %NL80211_ATTR_SSID attribute, and can optionally specify the association - * IEs in %NL80211_ATTR_IE, %NL80211_ATTR_AUTH_TYPE, %NL80211_ATTR_MAC, - * %NL80211_ATTR_WIPHY_FREQ, %NL80211_ATTR_CONTROL_PORT, + * IEs in %NL80211_ATTR_IE, %NL80211_ATTR_AUTH_TYPE, %NL80211_ATTR_USE_MFP, + * %NL80211_ATTR_MAC, %NL80211_ATTR_WIPHY_FREQ, %NL80211_ATTR_CONTROL_PORT, * %NL80211_ATTR_CONTROL_PORT_ETHERTYPE and * %NL80211_ATTR_CONTROL_PORT_NO_ENCRYPT. * Background scan period can optionally be @@ -958,7 +958,7 @@ enum nl80211_commands { * @NL80211_ATTR_USE_MFP: Whether management frame protection (IEEE 802.11w) is * used for the association (&enum nl80211_mfp, represented as a u32); * this attribute can be used - * with %NL80211_CMD_ASSOCIATE request + * with %NL80211_CMD_ASSOCIATE and %NL80211_CMD_CONNECT requests * * @NL80211_ATTR_STA_FLAGS2: Attribute containing a * &struct nl80211_sta_flag_update. -- cgit v1.2.3 From 11c4a075db2f8774d37544342c8cb9752b4db9e1 Mon Sep 17 00:00:00 2001 From: Simon Wunderlich Date: Tue, 8 Jan 2013 14:04:07 +0100 Subject: cfg80211: check radar interface combinations To ease further DFS development regarding interface combinations, use the interface combinations structure to test for radar capabilities. Drivers can specify which channel widths they support, and in which modes. Right now only a single AP interface is allowed, but as the DFS code evolves other combinations can be enabled. Signed-off-by: Simon Wunderlich Signed-off-by: Johannes Berg --- include/uapi/linux/nl80211.h | 3 +++ 1 file changed, 3 insertions(+) (limited to 'include/uapi/linux') diff --git a/include/uapi/linux/nl80211.h b/include/uapi/linux/nl80211.h index d01c16220dc5..e6eeb4ba5dc5 100644 --- a/include/uapi/linux/nl80211.h +++ b/include/uapi/linux/nl80211.h @@ -2984,6 +2984,8 @@ enum nl80211_iface_limit_attrs { * the infrastructure network's beacon interval. * @NL80211_IFACE_COMB_NUM_CHANNELS: u32 attribute specifying how many * different channels may be used within this group. + * @NL80211_IFACE_COMB_RADAR_DETECT_WIDTHS: u32 attribute containing the bitmap + * of supported channel widths for radar detection. * @NUM_NL80211_IFACE_COMB: number of attributes * @MAX_NL80211_IFACE_COMB: highest attribute number * @@ -3016,6 +3018,7 @@ enum nl80211_if_combination_attrs { NL80211_IFACE_COMB_MAXNUM, NL80211_IFACE_COMB_STA_AP_BI_MATCH, NL80211_IFACE_COMB_NUM_CHANNELS, + NL80211_IFACE_COMB_RADAR_DETECT_WIDTHS, /* keep last */ NUM_NL80211_IFACE_COMB, -- cgit v1.2.3 From 77765eaf5cfb6b8dd98ec8b54b411d74ff6095f1 Mon Sep 17 00:00:00 2001 From: Vasanthakumar Thiagarajan Date: Fri, 18 Jan 2013 11:18:45 +0530 Subject: cfg80211/nl80211: add API for MAC address ACLs Add API to enable drivers to implement MAC address based access control in AP/P2P GO mode. Capable drivers advertise this capability by setting the maximum number of MAC addresses in such a list in wiphy->max_acl_mac_addrs. An initial ACL may be given to the NL80211_CMD_START_AP command and/or changed later with NL80211_CMD_SET_MAC_ACL. Black- and whitelists are supported, but not simultaneously. Signed-off-by: Vasanthakumar Thiagarajan [rewrite commit log, many cleanups] Signed-off-by: Johannes Berg --- include/uapi/linux/nl80211.h | 51 ++++++++++++++++++++++++++++++++++++++++++-- 1 file changed, 49 insertions(+), 2 deletions(-) (limited to 'include/uapi/linux') diff --git a/include/uapi/linux/nl80211.h b/include/uapi/linux/nl80211.h index e6eeb4ba5dc5..5b7dbc1ea966 100644 --- a/include/uapi/linux/nl80211.h +++ b/include/uapi/linux/nl80211.h @@ -170,7 +170,8 @@ * %NL80211_ATTR_HIDDEN_SSID, %NL80211_ATTR_CIPHERS_PAIRWISE, * %NL80211_ATTR_CIPHER_GROUP, %NL80211_ATTR_WPA_VERSIONS, * %NL80211_ATTR_AKM_SUITES, %NL80211_ATTR_PRIVACY, - * %NL80211_ATTR_AUTH_TYPE and %NL80211_ATTR_INACTIVITY_TIMEOUT. + * %NL80211_ATTR_AUTH_TYPE, %NL80211_ATTR_INACTIVITY_TIMEOUT, + * %NL80211_ATTR_ACL_POLICY and %NL80211_ATTR_MAC_ADDRS. * The channel to use can be set on the interface or be given using the * %NL80211_ATTR_WIPHY_FREQ and the attributes determining channel width. * @NL80211_CMD_NEW_BEACON: old alias for %NL80211_CMD_START_AP @@ -586,6 +587,16 @@ * @NL80211_CMD_SET_MCAST_RATE: Change the rate used to send multicast frames * for IBSS or MESH vif. * + * @NL80211_CMD_SET_MAC_ACL: sets ACL for MAC address based access control. + * This is to be used with the drivers advertising the support of MAC + * address based access control. List of MAC addresses is passed in + * %NL80211_ATTR_MAC_ADDRS and ACL policy is passed in + * %NL80211_ATTR_ACL_POLICY. Driver will enable ACL with this list, if it + * is not already done. The new list will replace any existing list. Driver + * will clear its ACL when the list of MAC addresses passed is empty. This + * command is used in AP/P2P GO mode. Driver has to make sure to clear its + * ACL list during %NL80211_CMD_STOP_AP. + * * @NL80211_CMD_MAX: highest used command number * @__NL80211_CMD_AFTER_LAST: internal use */ @@ -736,6 +747,8 @@ enum nl80211_commands { NL80211_CMD_SET_MCAST_RATE, + NL80211_CMD_SET_MAC_ACL, + /* add new commands above here */ /* used to define NL80211_CMD_MAX below */ @@ -1313,6 +1326,16 @@ enum nl80211_commands { * @NL80211_ATTR_LOCAL_MESH_POWER_MODE: local mesh STA link-specific power mode * defined in &enum nl80211_mesh_power_mode. * + * @NL80211_ATTR_ACL_POLICY: ACL policy, see &enum nl80211_acl_policy, + * carried in a u32 attribute + * + * @NL80211_ATTR_MAC_ADDRS: Array of nested MAC addresses, used for + * MAC ACL. + * + * @NL80211_ATTR_MAC_ACL_MAX: u32 attribute to advertise the maximum + * number of MAC addresses that a device can support for MAC + * ACL. + * * @NL80211_ATTR_MAX: highest attribute number currently defined * @__NL80211_ATTR_AFTER_LAST: internal use */ @@ -1585,6 +1608,12 @@ enum nl80211_attrs { NL80211_ATTR_LOCAL_MESH_POWER_MODE, + NL80211_ATTR_ACL_POLICY, + + NL80211_ATTR_MAC_ADDRS, + + NL80211_ATTR_MAC_ACL_MAX, + /* add attributes here, update the policy in nl80211.c */ __NL80211_ATTR_AFTER_LAST, @@ -3248,7 +3277,7 @@ enum nl80211_probe_resp_offload_support_attr { * enum nl80211_connect_failed_reason - connection request failed reasons * @NL80211_CONN_FAIL_MAX_CLIENTS: Maximum number of clients that can be * handled by the AP is reached. - * @NL80211_CONN_FAIL_BLOCKED_CLIENT: Client's MAC is in the AP's blocklist. + * @NL80211_CONN_FAIL_BLOCKED_CLIENT: Connection request is rejected due to ACL. */ enum nl80211_connect_failed_reason { NL80211_CONN_FAIL_MAX_CLIENTS, @@ -3276,4 +3305,22 @@ enum nl80211_scan_flags { NL80211_SCAN_FLAG_AP = 1<<2, }; +/** + * enum nl80211_acl_policy - access control policy + * + * Access control policy is applied on a MAC list set by + * %NL80211_CMD_START_AP and %NL80211_CMD_SET_MAC_ACL, to + * be used with %NL80211_ATTR_ACL_POLICY. + * + * @NL80211_ACL_POLICY_ACCEPT_UNLESS_LISTED: Deny stations which are + * listed in ACL, i.e. allow all the stations which are not listed + * in ACL to authenticate. + * @NL80211_ACL_POLICY_DENY_UNLESS_LISTED: Allow the stations which are listed + * in ACL, i.e. deny all the stations which are not listed in ACL. + */ +enum nl80211_acl_policy { + NL80211_ACL_POLICY_ACCEPT_UNLESS_LISTED, + NL80211_ACL_POLICY_DENY_UNLESS_LISTED, +}; + #endif /* __LINUX_NL80211_H */ -- cgit v1.2.3