From 109086ce0b0f94760bdb0e8e2566ff8a2d673639 Mon Sep 17 00:00:00 2001 From: Arik Nemtsov Date: Wed, 28 Sep 2011 14:12:50 +0300 Subject: nl80211: support sending TDLS commands/frames Add support for sending high-level TDLS commands and TDLS frames via NL80211_CMD_TDLS_OPER and NL80211_CMD_TDLS_MGMT, respectively. Add appropriate cfg80211 callbacks for lower level drivers. Add wiphy capability flags for TDLS support and advertise them via nl80211. Signed-off-by: Arik Nemtsov Cc: Kalyan C Gaddam Signed-off-by: John W. Linville --- include/linux/nl80211.h | 42 ++++++++++++++++++++++++++++++++++++++++++ 1 file changed, 42 insertions(+) (limited to 'include/linux') diff --git a/include/linux/nl80211.h b/include/linux/nl80211.h index c73582fb9d20..a5ab23df5b17 100644 --- a/include/linux/nl80211.h +++ b/include/linux/nl80211.h @@ -506,6 +506,9 @@ * @NL80211_CMD_PMKSA_CANDIDATE: This is used as an event to inform userspace * of PMKSA caching dandidates. * + * @NL80211_CMD_TDLS_OPER: Perform a high-level TDLS command (e.g. link setup). + * @NL80211_CMD_TDLS_MGMT: Send a TDLS management frame. + * * @NL80211_CMD_MAX: highest used command number * @__NL80211_CMD_AFTER_LAST: internal use */ @@ -632,6 +635,9 @@ enum nl80211_commands { NL80211_CMD_PMKSA_CANDIDATE, + NL80211_CMD_TDLS_OPER, + NL80211_CMD_TDLS_MGMT, + /* add new commands above here */ /* used to define NL80211_CMD_MAX below */ @@ -1089,6 +1095,20 @@ enum nl80211_commands { * This attribute is used with %NL80211_CMD_TRIGGER_SCAN and * %NL80211_CMD_FRAME commands. * + * @NL80211_ATTR_TDLS_ACTION: Low level TDLS action code (e.g. link setup + * request, link setup confirm, link teardown, etc.). Values are + * described in the TDLS (802.11z) specification. + * @NL80211_ATTR_TDLS_DIALOG_TOKEN: Non-zero token for uniquely identifying a + * TDLS conversation between two devices. + * @NL80211_ATTR_TDLS_OPERATION: High level TDLS operation; see + * &enum nl80211_tdls_operation, represented as a u8. + * @NL80211_ATTR_TDLS_SUPPORT: A flag indicating the device can operate + * as a TDLS peer sta. + * @NL80211_ATTR_TDLS_EXTERNAL_SETUP: The TDLS discovery/setup and teardown + * procedures should be performed by sending TDLS packets via + * %NL80211_CMD_TDLS_MGMT. Otherwise %NL80211_CMD_TDLS_OPER should be + * used for asking the driver to perform a TDLS operation. + * * @NL80211_ATTR_MAX: highest attribute number currently defined * @__NL80211_ATTR_AFTER_LAST: internal use */ @@ -1311,6 +1331,12 @@ enum nl80211_attrs { NL80211_ATTR_TX_NO_CCK_RATE, + NL80211_ATTR_TDLS_ACTION, + NL80211_ATTR_TDLS_DIALOG_TOKEN, + NL80211_ATTR_TDLS_OPERATION, + NL80211_ATTR_TDLS_SUPPORT, + NL80211_ATTR_TDLS_EXTERNAL_SETUP, + /* add attributes here, update the policy in nl80211.c */ __NL80211_ATTR_AFTER_LAST, @@ -2604,4 +2630,20 @@ enum nl80211_pmksa_candidate_attr { MAX_NL80211_PMKSA_CANDIDATE = NUM_NL80211_PMKSA_CANDIDATE - 1 }; +/** + * enum nl80211_tdls_operation - values for %NL80211_ATTR_TDLS_OPERATION + * @NL80211_TDLS_DISCOVERY_REQ: Send a TDLS discovery request + * @NL80211_TDLS_SETUP: Setup TDLS link + * @NL80211_TDLS_TEARDOWN: Teardown a TDLS link which is already established + * @NL80211_TDLS_ENABLE_LINK: Enable TDLS link + * @NL80211_TDLS_DISABLE_LINK: Disable TDLS link + */ +enum nl80211_tdls_operation { + NL80211_TDLS_DISCOVERY_REQ, + NL80211_TDLS_SETUP, + NL80211_TDLS_TEARDOWN, + NL80211_TDLS_ENABLE_LINK, + NL80211_TDLS_DISABLE_LINK, +}; + #endif /* __LINUX_NL80211_H */ -- cgit v1.2.3 From dfe018bf99537e42c816d3f543620a7e09fcf3cd Mon Sep 17 00:00:00 2001 From: Arik Nemtsov Date: Wed, 28 Sep 2011 14:12:52 +0300 Subject: mac80211: handle TDLS high-level commands and frames Register and implement the TDLS cfg80211 callback functions. Internally prepare and send TDLS management frames. We incorporate local STA capabilities and supported rates with extra IEs given by usermode. The resulting packet is either encapsulated in a data frame, or assembled as an action frame. It is transmitted either directly or through the AP, as mandated by the TDLS specification. Declare support for the TDLS external setup wiphy capability. This tells usermode to handle link setup and discovery on its own, and use the kernel driver for sending TDLS mgmt packets. Signed-off-by: Arik Nemtsov Cc: Kalyan C Gaddam Signed-off-by: John W. Linville --- include/linux/ieee80211.h | 85 +++++++++++++++++++++++++++++++++++++++++++++++ include/linux/if_ether.h | 1 + 2 files changed, 86 insertions(+) (limited to 'include/linux') diff --git a/include/linux/ieee80211.h b/include/linux/ieee80211.h index b5e0a5c344fd..48363c3c40f8 100644 --- a/include/linux/ieee80211.h +++ b/include/linux/ieee80211.h @@ -759,6 +759,12 @@ struct ieee80211_mgmt { u8 action; u8 smps_control; } __attribute__ ((packed)) ht_smps; + struct { + u8 action_code; + u8 dialog_token; + __le16 capability; + u8 variable[0]; + } __packed tdls_discover_resp; } u; } __attribute__ ((packed)) action; } u; @@ -805,6 +811,52 @@ struct ieee80211_pspoll { u8 ta[6]; } __attribute__ ((packed)); +/* TDLS */ + +/* Link-id information element */ +struct ieee80211_tdls_lnkie { + u8 ie_type; /* Link Identifier IE */ + u8 ie_len; + u8 bssid[6]; + u8 init_sta[6]; + u8 resp_sta[6]; +} __packed; + +struct ieee80211_tdls_data { + u8 da[6]; + u8 sa[6]; + __be16 ether_type; + u8 payload_type; + u8 category; + u8 action_code; + union { + struct { + u8 dialog_token; + __le16 capability; + u8 variable[0]; + } __packed setup_req; + struct { + __le16 status_code; + u8 dialog_token; + __le16 capability; + u8 variable[0]; + } __packed setup_resp; + struct { + __le16 status_code; + u8 dialog_token; + u8 variable[0]; + } __packed setup_cfm; + struct { + __le16 reason_code; + u8 variable[0]; + } __packed teardown; + struct { + u8 dialog_token; + u8 variable[0]; + } __packed discover_req; + } u; +} __packed; + /** * struct ieee80211_bar - HT Block Ack Request * @@ -1196,6 +1248,8 @@ enum ieee80211_eid { WLAN_EID_TS_DELAY = 43, WLAN_EID_TCLAS_PROCESSING = 44, WLAN_EID_QOS_CAPA = 46, + /* 802.11z */ + WLAN_EID_LINK_ID = 101, /* 802.11s */ WLAN_EID_MESH_CONFIG = 113, WLAN_EID_MESH_ID = 114, @@ -1279,6 +1333,7 @@ enum ieee80211_category { WLAN_CATEGORY_HT = 7, WLAN_CATEGORY_SA_QUERY = 8, WLAN_CATEGORY_PROTECTED_DUAL_OF_ACTION = 9, + WLAN_CATEGORY_TDLS = 12, WLAN_CATEGORY_MESH_ACTION = 13, WLAN_CATEGORY_MULTIHOP_ACTION = 14, WLAN_CATEGORY_SELF_PROTECTED = 15, @@ -1342,6 +1397,36 @@ enum ieee80211_key_len { WLAN_KEY_LEN_AES_CMAC = 16, }; +/* Public action codes */ +enum ieee80211_pub_actioncode { + WLAN_PUB_ACTION_TDLS_DISCOVER_RES = 14, +}; + +/* TDLS action codes */ +enum ieee80211_tdls_actioncode { + WLAN_TDLS_SETUP_REQUEST = 0, + WLAN_TDLS_SETUP_RESPONSE = 1, + WLAN_TDLS_SETUP_CONFIRM = 2, + WLAN_TDLS_TEARDOWN = 3, + WLAN_TDLS_PEER_TRAFFIC_INDICATION = 4, + WLAN_TDLS_CHANNEL_SWITCH_REQUEST = 5, + WLAN_TDLS_CHANNEL_SWITCH_RESPONSE = 6, + WLAN_TDLS_PEER_PSM_REQUEST = 7, + WLAN_TDLS_PEER_PSM_RESPONSE = 8, + WLAN_TDLS_PEER_TRAFFIC_RESPONSE = 9, + WLAN_TDLS_DISCOVERY_REQUEST = 10, +}; + +/* + * TDLS capabililites to be enabled in the 5th byte of the + * @WLAN_EID_EXT_CAPABILITY information element + */ +#define WLAN_EXT_CAPA5_TDLS_ENABLED BIT(5) +#define WLAN_EXT_CAPA5_TDLS_PROHIBITED BIT(6) + +/* TDLS specific payload type in the LLC/SNAP header */ +#define WLAN_TDLS_SNAP_RFTYPE 0x2 + /** * enum - mesh path selection protocol identifier * diff --git a/include/linux/if_ether.h b/include/linux/if_ether.h index a3d99ff6e3b5..49c38fc8dbc3 100644 --- a/include/linux/if_ether.h +++ b/include/linux/if_ether.h @@ -83,6 +83,7 @@ #define ETH_P_8021AH 0x88E7 /* 802.1ah Backbone Service Tag */ #define ETH_P_1588 0x88F7 /* IEEE 1588 Timesync */ #define ETH_P_FCOE 0x8906 /* Fibre Channel over Ethernet */ +#define ETH_P_TDLS 0x890D /* TDLS */ #define ETH_P_FIP 0x8914 /* FCoE Initialization Protocol */ #define ETH_P_QINQ1 0x9100 /* deprecated QinQ VLAN [ NOT AN OFFICIALLY REGISTERED ID ] */ #define ETH_P_QINQ2 0x9200 /* deprecated QinQ VLAN [ NOT AN OFFICIALLY REGISTERED ID ] */ -- cgit v1.2.3 From 07ba55d7f1d0da174c9bc545c713b44cee760197 Mon Sep 17 00:00:00 2001 From: Arik Nemtsov Date: Wed, 28 Sep 2011 14:12:53 +0300 Subject: nl80211/mac80211: allow adding TDLS peers as stations When adding a TDLS peer STA, mark it with a new flag in both nl80211 and mac80211. Before adding a peer, make sure the wiphy supports TDLS and our operating mode is appropriate (managed). In addition, make sure all peers are removed on disassociation. A TDLS peer is first added just before link setup is initiated. In later setup stages we have more info about peer supported rates, capabilities, etc. This info is reported via nl80211_set_station(). Signed-off-by: Arik Nemtsov Cc: Kalyan C Gaddam Signed-off-by: John W. Linville --- include/linux/nl80211.h | 2 ++ 1 file changed, 2 insertions(+) (limited to 'include/linux') diff --git a/include/linux/nl80211.h b/include/linux/nl80211.h index a5ab23df5b17..9d797f253d8e 100644 --- a/include/linux/nl80211.h +++ b/include/linux/nl80211.h @@ -1434,6 +1434,7 @@ enum nl80211_iftype { * @NL80211_STA_FLAG_WME: station is WME/QoS capable * @NL80211_STA_FLAG_MFP: station uses management frame protection * @NL80211_STA_FLAG_AUTHENTICATED: station is authenticated + * @NL80211_STA_FLAG_TDLS_PEER: station is a TDLS peer * @NL80211_STA_FLAG_MAX: highest station flag number currently defined * @__NL80211_STA_FLAG_AFTER_LAST: internal use */ @@ -1444,6 +1445,7 @@ enum nl80211_sta_flags { NL80211_STA_FLAG_WME, NL80211_STA_FLAG_MFP, NL80211_STA_FLAG_AUTHENTICATED, + NL80211_STA_FLAG_TDLS_PEER, /* keep last */ __NL80211_STA_FLAG_AFTER_LAST, -- cgit v1.2.3 From e209c5a7ed1870ab7f112ad47083b5d616e8b6a4 Mon Sep 17 00:00:00 2001 From: Sangwook Lee Date: Thu, 29 Sep 2011 12:57:17 +0100 Subject: net:rfkill: add a gpio setup function into GPIO rfkill Add a gpio setup function which gives a chance to set up platform specific configuration such as pin multiplexing, input/output direction at the runtime or booting time. Signed-off-by: Sangwook Lee Signed-off-by: John W. Linville --- include/linux/rfkill-gpio.h | 4 ++++ 1 file changed, 4 insertions(+) (limited to 'include/linux') diff --git a/include/linux/rfkill-gpio.h b/include/linux/rfkill-gpio.h index a175d0598033..4d09f6eab359 100644 --- a/include/linux/rfkill-gpio.h +++ b/include/linux/rfkill-gpio.h @@ -30,6 +30,8 @@ * @reset_gpio: GPIO which is used for reseting rfkill switch * @shutdown_gpio: GPIO which is used for shutdown of rfkill switch * @power_clk_name: [optional] name of clk to turn off while blocked + * @gpio_runtime_close: clean up platform specific gpio configuration + * @gpio_runtime_setup: set up platform specific gpio configuration */ struct rfkill_gpio_platform_data { @@ -38,6 +40,8 @@ struct rfkill_gpio_platform_data { int shutdown_gpio; const char *power_clk_name; enum rfkill_type type; + void (*gpio_runtime_close)(struct platform_device *); + int (*gpio_runtime_setup)(struct platform_device *); }; #endif /* __RFKILL_GPIO_H */ -- cgit v1.2.3