diff options
Diffstat (limited to 'include/net/mac80211.h')
| -rw-r--r-- | include/net/mac80211.h | 511 |
1 files changed, 361 insertions, 150 deletions
diff --git a/include/net/mac80211.h b/include/net/mac80211.h index d52914b75331..6b1077c2a63f 100644 --- a/include/net/mac80211.h +++ b/include/net/mac80211.h @@ -84,6 +84,39 @@ * */ +/** + * DOC: mac80211 software tx queueing + * + * mac80211 provides an optional intermediate queueing implementation designed + * to allow the driver to keep hardware queues short and provide some fairness + * between different stations/interfaces. + * In this model, the driver pulls data frames from the mac80211 queue instead + * of letting mac80211 push them via drv_tx(). + * Other frames (e.g. control or management) are still pushed using drv_tx(). + * + * Drivers indicate that they use this model by implementing the .wake_tx_queue + * driver operation. + * + * Intermediate queues (struct ieee80211_txq) are kept per-sta per-tid, with a + * single per-vif queue for multicast data frames. + * + * The driver is expected to initialize its private per-queue data for stations + * and interfaces in the .add_interface and .sta_add ops. + * + * The driver can't access the queue directly. To dequeue a frame, it calls + * ieee80211_tx_dequeue(). Whenever mac80211 adds a new frame to a queue, it + * calls the .wake_tx_queue driver op. + * + * For AP powersave TIM handling, the driver only needs to indicate if it has + * buffered packets in the driver specific data structures by calling + * ieee80211_sta_set_buffered(). For frames buffered in the ieee80211_txq + * struct, mac80211 sets the appropriate TIM PVB bits and calls + * .release_buffered_frames(). + * In that callback the driver is therefore expected to release its own + * buffered frames and afterwards also frames from the ieee80211_txq (obtained + * via the usual ieee80211_tx_dequeue). + */ + struct device; /** @@ -301,17 +334,107 @@ enum ieee80211_bss_change { #define IEEE80211_BSS_ARP_ADDR_LIST_LEN 4 /** - * enum ieee80211_rssi_event - RSSI threshold event - * An indicator for when RSSI goes below/above a certain threshold. - * @RSSI_EVENT_HIGH: AP's rssi crossed the high threshold set by the driver. - * @RSSI_EVENT_LOW: AP's rssi crossed the low threshold set by the driver. + * enum ieee80211_event_type - event to be notified to the low level driver + * @RSSI_EVENT: AP's rssi crossed the a threshold set by the driver. + * @MLME_EVENT: event related to MLME + * @BAR_RX_EVENT: a BAR was received + * @BA_FRAME_TIMEOUT: Frames were released from the reordering buffer because + * they timed out. This won't be called for each frame released, but only + * once each time the timeout triggers. + */ +enum ieee80211_event_type { + RSSI_EVENT, + MLME_EVENT, + BAR_RX_EVENT, + BA_FRAME_TIMEOUT, +}; + +/** + * enum ieee80211_rssi_event_data - relevant when event type is %RSSI_EVENT + * @RSSI_EVENT_HIGH: AP's rssi went below the threshold set by the driver. + * @RSSI_EVENT_LOW: AP's rssi went above the threshold set by the driver. */ -enum ieee80211_rssi_event { +enum ieee80211_rssi_event_data { RSSI_EVENT_HIGH, RSSI_EVENT_LOW, }; /** + * struct ieee80211_rssi_event - data attached to an %RSSI_EVENT + * @data: See &enum ieee80211_rssi_event_data + */ +struct ieee80211_rssi_event { + enum ieee80211_rssi_event_data data; +}; + +/** + * enum ieee80211_mlme_event_data - relevant when event type is %MLME_EVENT + * @AUTH_EVENT: the MLME operation is authentication + * @ASSOC_EVENT: the MLME operation is association + * @DEAUTH_RX_EVENT: deauth received.. + * @DEAUTH_TX_EVENT: deauth sent. + */ +enum ieee80211_mlme_event_data { + AUTH_EVENT, + ASSOC_EVENT, + DEAUTH_RX_EVENT, + DEAUTH_TX_EVENT, +}; + +/** + * enum ieee80211_mlme_event_status - relevant when event type is %MLME_EVENT + * @MLME_SUCCESS: the MLME operation completed successfully. + * @MLME_DENIED: the MLME operation was denied by the peer. + * @MLME_TIMEOUT: the MLME operation timed out. + */ +enum ieee80211_mlme_event_status { + MLME_SUCCESS, + MLME_DENIED, + MLME_TIMEOUT, +}; + +/** + * struct ieee80211_mlme_event - data attached to an %MLME_EVENT + * @data: See &enum ieee80211_mlme_event_data + * @status: See &enum ieee80211_mlme_event_status + * @reason: the reason code if applicable + */ +struct ieee80211_mlme_event { + enum ieee80211_mlme_event_data data; + enum ieee80211_mlme_event_status status; + u16 reason; +}; + +/** + * struct ieee80211_ba_event - data attached for BlockAck related events + * @sta: pointer to the &ieee80211_sta to which this event relates + * @tid: the tid + * @ssn: the starting sequence number (for %BAR_RX_EVENT) + */ +struct ieee80211_ba_event { + struct ieee80211_sta *sta; + u16 tid; + u16 ssn; +}; + +/** + * struct ieee80211_event - event to be sent to the driver + * @type: The event itself. See &enum ieee80211_event_type. + * @rssi: relevant if &type is %RSSI_EVENT + * @mlme: relevant if &type is %AUTH_EVENT + * @ba: relevant if &type is %BAR_RX_EVENT or %BA_FRAME_TIMEOUT + * @u:union holding the fields above + */ +struct ieee80211_event { + enum ieee80211_event_type type; + union { + struct ieee80211_rssi_event rssi; + struct ieee80211_mlme_event mlme; + struct ieee80211_ba_event ba; + } u; +}; + +/** * struct ieee80211_bss_conf - holds the BSS's changing parameters * * This structure keeps information about a BSS (and an association @@ -323,12 +446,8 @@ enum ieee80211_rssi_event { * @ibss_creator: indicates if a new IBSS network is being created * @aid: association ID number, valid only when @assoc is true * @use_cts_prot: use CTS protection - * @use_short_preamble: use 802.11b short preamble; - * if the hardware cannot handle this it must set the - * IEEE80211_HW_2GHZ_SHORT_PREAMBLE_INCAPABLE hardware flag - * @use_short_slot: use short slot time (only relevant for ERP); - * if the hardware cannot handle this it must set the - * IEEE80211_HW_2GHZ_SHORT_SLOT_INCAPABLE hardware flag + * @use_short_preamble: use 802.11b short preamble + * @use_short_slot: use short slot time (only relevant for ERP) * @dtim_period: num of beacons before the next DTIM, for beaconing, * valid in station mode only if after the driver was notified * with the %BSS_CHANGED_BEACON_INFO flag, will be non-zero then. @@ -337,12 +456,15 @@ enum ieee80211_rssi_event { * HW flag %IEEE80211_HW_TIMING_BEACON_ONLY is set, then this can * only come from a beacon, but might not become valid until after * association when a beacon is received (which is notified with the - * %BSS_CHANGED_DTIM flag.) + * %BSS_CHANGED_DTIM flag.). See also sync_dtim_count important notice. * @sync_device_ts: the device timestamp corresponding to the sync_tsf, * the driver/device can use this to calculate synchronisation - * (see @sync_tsf) + * (see @sync_tsf). See also sync_dtim_count important notice. * @sync_dtim_count: Only valid when %IEEE80211_HW_TIMING_BEACON_ONLY * is requested, see @sync_tsf/@sync_device_ts. + * IMPORTANT: These three sync_* parameters would possibly be out of sync + * by the time the driver will use them. The synchronized view is currently + * guaranteed only in certain callbacks. * @beacon_int: beacon interval * @assoc_capability: capabilities taken from assoc resp * @basic_rates: bitmap of basic rates, each bit stands for an @@ -749,6 +871,9 @@ struct ieee80211_tx_info { /* 4 bytes free */ } control; struct { + u64 cookie; + } ack; + struct { struct ieee80211_tx_rate rates[IEEE80211_TX_MAX_RATES]; s32 ack_signal; u8 ampdu_ack_len; @@ -1234,6 +1359,7 @@ enum ieee80211_vif_flags { * monitor interface (if that is requested.) * @drv_priv: data area for driver use, will always be aligned to * sizeof(void *). + * @txq: the multicast data TX queue (if driver uses the TXQ abstraction) */ struct ieee80211_vif { enum nl80211_iftype type; @@ -1245,6 +1371,8 @@ struct ieee80211_vif { u8 cab_queue; u8 hw_queue[IEEE80211_NUM_ACS]; + struct ieee80211_txq *txq; + struct ieee80211_chanctx_conf __rcu *chanctx_conf; u32 driver_flags; @@ -1279,6 +1407,19 @@ static inline bool ieee80211_vif_is_mesh(struct ieee80211_vif *vif) struct ieee80211_vif *wdev_to_ieee80211_vif(struct wireless_dev *wdev); /** + * ieee80211_vif_to_wdev - return a wdev struct from a vif + * @vif: the vif to get the wdev for + * + * This can be used by mac80211 drivers with direct cfg80211 APIs + * (like the vendor commands) that needs to get the wdev for a vif. + * + * Note that this function may return %NULL if the given wdev isn't + * associated with a vif that the driver knows about (e.g. monitor + * or AP_VLAN interfaces.) + */ +struct wireless_dev *ieee80211_vif_to_wdev(struct ieee80211_vif *vif); + +/** * enum ieee80211_key_flags - key flags * * These flags are used for communication about keys between the driver @@ -1337,6 +1478,9 @@ enum ieee80211_key_flags { * wants to be given when a frame is transmitted and needs to be * encrypted in hardware. * @cipher: The key's cipher suite selector. + * @tx_pn: PN used for TX on non-TKIP keys, may be used by the driver + * as well if it needs to do software PN assignment by itself + * (e.g. due to TSO) * @flags: key flags, see &enum ieee80211_key_flags. * @keyidx: the key index (0-3) * @keylen: key material length @@ -1349,6 +1493,7 @@ enum ieee80211_key_flags { * @iv_len: The IV length for this key type */ struct ieee80211_key_conf { + atomic64_t tx_pn; u32 cipher; u8 icv_len; u8 iv_len; @@ -1359,6 +1504,47 @@ struct ieee80211_key_conf { u8 key[0]; }; +#define IEEE80211_MAX_PN_LEN 16 + +/** + * struct ieee80211_key_seq - key sequence counter + * + * @tkip: TKIP data, containing IV32 and IV16 in host byte order + * @ccmp: PN data, most significant byte first (big endian, + * reverse order than in packet) + * @aes_cmac: PN data, most significant byte first (big endian, + * reverse order than in packet) + * @aes_gmac: PN data, most significant byte first (big endian, + * reverse order than in packet) + * @gcmp: PN data, most significant byte first (big endian, + * reverse order than in packet) + * @hw: data for HW-only (e.g. cipher scheme) keys + */ +struct ieee80211_key_seq { + union { + struct { + u32 iv32; + u16 iv16; + } tkip; + struct { + u8 pn[6]; + } ccmp; + struct { + u8 pn[6]; + } aes_cmac; + struct { + u8 pn[6]; + } aes_gmac; + struct { + u8 pn[6]; + } gcmp; + struct { + u8 seq[IEEE80211_MAX_PN_LEN]; + u8 seq_len; + } hw; + }; +}; + /** * struct ieee80211_cipher_scheme - cipher scheme * @@ -1472,7 +1658,8 @@ struct ieee80211_sta_rates { * @supp_rates: Bitmap of supported rates (per band) * @ht_cap: HT capabilities of this STA; restricted to our own capabilities * @vht_cap: VHT capabilities of this STA; restricted to our own capabilities - * @wme: indicates whether the STA supports QoS/WME. + * @wme: indicates whether the STA supports QoS/WME (if local devices does, + * otherwise always false) * @drv_priv: data area for driver use, will always be aligned to * sizeof(void *), size is determined in hw information. * @uapsd_queues: bitmap of queues configured for uapsd. Only valid @@ -1488,6 +1675,8 @@ struct ieee80211_sta_rates { * @tdls: indicates whether the STA is a TDLS peer * @tdls_initiator: indicates the STA is an initiator of the TDLS link. Only * valid if the STA is a TDLS peer in the first place. + * @mfp: indicates whether the STA uses management frame protection or not. + * @txq: per-TID data TX queues (if driver uses the TXQ abstraction) */ struct ieee80211_sta { u32 supp_rates[IEEE80211_NUM_BANDS]; @@ -1504,6 +1693,9 @@ struct ieee80211_sta { struct ieee80211_sta_rates __rcu *rates; bool tdls; bool tdls_initiator; + bool mfp; + + struct ieee80211_txq *txq[IEEE80211_NUM_TIDS]; /* must be last */ u8 drv_priv[0] __aligned(sizeof(void *)); @@ -1533,6 +1725,28 @@ struct ieee80211_tx_control { }; /** + * struct ieee80211_txq - Software intermediate tx queue + * + * @vif: &struct ieee80211_vif pointer from the add_interface callback. + * @sta: station table entry, %NULL for per-vif queue + * @tid: the TID for this queue (unused for per-vif queue) + * @ac: the AC for this queue + * @drv_priv: driver private area, sized by hw->txq_data_size + * + * The driver can obtain packets from this queue by calling + * ieee80211_tx_dequeue(). + */ +struct ieee80211_txq { + struct ieee80211_vif *vif; + struct ieee80211_sta *sta; + u8 tid; + u8 ac; + + /* must be last */ + u8 drv_priv[0] __aligned(sizeof(void *)); +}; + +/** * enum ieee80211_hw_flags - hardware flags * * These flags are used to indicate hardware capabilities to @@ -1566,13 +1780,6 @@ struct ieee80211_tx_control { * multicast frames when there are power saving stations so that * the driver can fetch them with ieee80211_get_buffered_bc(). * - * @IEEE80211_HW_2GHZ_SHORT_SLOT_INCAPABLE: - * Hardware is not capable of short slot operation on the 2.4 GHz band. - * - * @IEEE80211_HW_2GHZ_SHORT_PREAMBLE_INCAPABLE: - * Hardware is not capable of receiving frames with short preamble on - * the 2.4 GHz band. - * * @IEEE80211_HW_SIGNAL_UNSPEC: * Hardware can provide signal values but we don't know its units. We * expect values between 0 and @max_signal. @@ -1647,6 +1854,10 @@ struct ieee80211_tx_control { * the driver returns 1. This also forces the driver to advertise its * supported cipher suites. * + * @IEEE80211_HW_SUPPORT_FAST_XMIT: The driver/hardware supports fast-xmit, + * this currently requires only the ability to calculate the duration + * for frames. + * * @IEEE80211_HW_QUEUE_CONTROL: The driver wants to control per-interface * queue mapping in order to use different queues (not just one per AC) * for different virtual interfaces. See the doc section on HW queue @@ -1674,41 +1885,44 @@ struct ieee80211_tx_control { * @IEEE80211_HW_SUPPORTS_CLONED_SKBS: The driver will never modify the payload * or tailroom of TX skbs without copying them first. * - * @IEEE80211_SINGLE_HW_SCAN_ON_ALL_BANDS: The HW supports scanning on all bands + * @IEEE80211_HW_SINGLE_SCAN_ON_ALL_BANDS: The HW supports scanning on all bands * in one command, mac80211 doesn't have to run separate scans per band. + * + * @NUM_IEEE80211_HW_FLAGS: number of hardware flags, used for sizing arrays */ enum ieee80211_hw_flags { - IEEE80211_HW_HAS_RATE_CONTROL = 1<<0, - IEEE80211_HW_RX_INCLUDES_FCS = 1<<1, - IEEE80211_HW_HOST_BROADCAST_PS_BUFFERING = 1<<2, - IEEE80211_HW_2GHZ_SHORT_SLOT_INCAPABLE = 1<<3, - IEEE80211_HW_2GHZ_SHORT_PREAMBLE_INCAPABLE = 1<<4, - IEEE80211_HW_SIGNAL_UNSPEC = 1<<5, - IEEE80211_HW_SIGNAL_DBM = 1<<6, - IEEE80211_HW_NEED_DTIM_BEFORE_ASSOC = 1<<7, - IEEE80211_HW_SPECTRUM_MGMT = 1<<8, - IEEE80211_HW_AMPDU_AGGREGATION = 1<<9, - IEEE80211_HW_SUPPORTS_PS = 1<<10, - IEEE80211_HW_PS_NULLFUNC_STACK = 1<<11, - IEEE80211_HW_SUPPORTS_DYNAMIC_PS = 1<<12, - IEEE80211_HW_MFP_CAPABLE = 1<<13, - IEEE80211_HW_WANT_MONITOR_VIF = 1<<14, - IEEE80211_HW_NO_AUTO_VIF = 1<<15, - IEEE80211_HW_SW_CRYPTO_CONTROL = 1<<16, - /* free slots */ - IEEE80211_HW_REPORTS_TX_ACK_STATUS = 1<<18, - IEEE80211_HW_CONNECTION_MONITOR = 1<<19, - IEEE80211_HW_QUEUE_CONTROL = 1<<20, - IEEE80211_HW_SUPPORTS_PER_STA_GTK = 1<<21, - IEEE80211_HW_AP_LINK_PS = 1<<22, - IEEE80211_HW_TX_AMPDU_SETUP_IN_HW = 1<<23, - IEEE80211_HW_SUPPORTS_RC_TABLE = 1<<24, - IEEE80211_HW_P2P_DEV_ADDR_FOR_INTF = 1<<25, - IEEE80211_HW_TIMING_BEACON_ONLY = 1<<26, - IEEE80211_HW_SUPPORTS_HT_CCK_RATES = 1<<27, - IEEE80211_HW_CHANCTX_STA_CSA = 1<<28, - IEEE80211_HW_SUPPORTS_CLONED_SKBS = 1<<29, - IEEE80211_SINGLE_HW_SCAN_ON_ALL_BANDS = 1<<30, + IEEE80211_HW_HAS_RATE_CONTROL, + IEEE80211_HW_RX_INCLUDES_FCS, + IEEE80211_HW_HOST_BROADCAST_PS_BUFFERING, + IEEE80211_HW_SIGNAL_UNSPEC, + IEEE80211_HW_SIGNAL_DBM, + IEEE80211_HW_NEED_DTIM_BEFORE_ASSOC, + IEEE80211_HW_SPECTRUM_MGMT, + IEEE80211_HW_AMPDU_AGGREGATION, + IEEE80211_HW_SUPPORTS_PS, + IEEE80211_HW_PS_NULLFUNC_STACK, + IEEE80211_HW_SUPPORTS_DYNAMIC_PS, + IEEE80211_HW_MFP_CAPABLE, + IEEE80211_HW_WANT_MONITOR_VIF, + IEEE80211_HW_NO_AUTO_VIF, + IEEE80211_HW_SW_CRYPTO_CONTROL, + IEEE80211_HW_SUPPORT_FAST_XMIT, + IEEE80211_HW_REPORTS_TX_ACK_STATUS, + IEEE80211_HW_CONNECTION_MONITOR, + IEEE80211_HW_QUEUE_CONTROL, + IEEE80211_HW_SUPPORTS_PER_STA_GTK, + IEEE80211_HW_AP_LINK_PS, + IEEE80211_HW_TX_AMPDU_SETUP_IN_HW, + IEEE80211_HW_SUPPORTS_RC_TABLE, + IEEE80211_HW_P2P_DEV_ADDR_FOR_INTF, + IEEE80211_HW_TIMING_BEACON_ONLY, + IEEE80211_HW_SUPPORTS_HT_CCK_RATES, + IEEE80211_HW_CHANCTX_STA_CSA, + IEEE80211_HW_SUPPORTS_CLONED_SKBS, + IEEE80211_HW_SINGLE_SCAN_ON_ALL_BANDS, + + /* keep last, obviously */ + NUM_IEEE80211_HW_FLAGS }; /** @@ -1756,6 +1970,8 @@ enum ieee80211_hw_flags { * within &struct ieee80211_sta. * @chanctx_data_size: size (in bytes) of the drv_priv data area * within &struct ieee80211_chanctx_conf. + * @txq_data_size: size (in bytes) of the drv_priv data area + * within @struct ieee80211_txq. * * @max_rates: maximum number of alternate rate retry stages the hw * can handle. @@ -1787,8 +2003,8 @@ enum ieee80211_hw_flags { * Use the %IEEE80211_RADIOTAP_VHT_KNOWN_* values. * * @netdev_features: netdev features to be set in each netdev created - * from this HW. Note only HW checksum features are currently - * compatible with mac80211. Other feature bits will be rejected. + * from this HW. Note that not all features are usable with mac80211, + * other features will be rejected during HW registration. * * @uapsd_queues: This bitmap is included in (re)association frame to indicate * for each access category if it is uAPSD trigger-enabled and delivery- @@ -1804,18 +2020,22 @@ enum ieee80211_hw_flags { * @n_cipher_schemes: a size of an array of cipher schemes definitions. * @cipher_schemes: a pointer to an array of cipher scheme definitions * supported by HW. + * + * @txq_ac_max_pending: maximum number of frames per AC pending in all txq + * entries for a vif. */ struct ieee80211_hw { struct ieee80211_conf conf; struct wiphy *wiphy; const char *rate_control_algorithm; void *priv; - u32 flags; + unsigned long flags[BITS_TO_LONGS(NUM_IEEE80211_HW_FLAGS)]; unsigned int extra_tx_headroom; unsigned int extra_beacon_tailroom; int vif_data_size; int sta_data_size; int chanctx_data_size; + int txq_data_size; u16 queues; u16 max_listen_interval; s8 max_signal; @@ -1832,8 +2052,23 @@ struct ieee80211_hw { u8 uapsd_max_sp_len; u8 n_cipher_schemes; const struct ieee80211_cipher_scheme *cipher_schemes; + int txq_ac_max_pending; }; +static inline bool _ieee80211_hw_check(struct ieee80211_hw *hw, + enum ieee80211_hw_flags flg) +{ + return test_bit(flg, hw->flags); +} +#define ieee80211_hw_check(hw, flg) _ieee80211_hw_check(hw, IEEE80211_HW_##flg) + +static inline void _ieee80211_hw_set(struct ieee80211_hw *hw, + enum ieee80211_hw_flags flg) +{ + return __set_bit(flg, hw->flags); +} +#define ieee80211_hw_set(hw, flg) _ieee80211_hw_set(hw, IEEE80211_HW_##flg) + /** * struct ieee80211_scan_request - hw scan request * @@ -2347,10 +2582,6 @@ void ieee80211_free_txskb(struct ieee80211_hw *hw, struct sk_buff *skb); * stack. It is always safe to pass more frames than requested, * but this has negative impact on power consumption. * - * @FIF_PROMISC_IN_BSS: promiscuous mode within your BSS, - * think of the BSS as your network segment and then this corresponds - * to the regular ethernet device promiscuous mode. - * * @FIF_ALLMULTI: pass all multicast frames, this is used if requested * by the user or if the hardware is not capable of filtering by * multicast address. @@ -2367,18 +2598,16 @@ void ieee80211_free_txskb(struct ieee80211_hw *hw, struct sk_buff *skb); * mac80211 needs to do and the amount of CPU wakeups, so you should * honour this flag if possible. * - * @FIF_CONTROL: pass control frames (except for PS Poll), if PROMISC_IN_BSS - * is not set then only those addressed to this station. + * @FIF_CONTROL: pass control frames (except for PS Poll) addressed to this + * station * * @FIF_OTHER_BSS: pass frames destined to other BSSes * - * @FIF_PSPOLL: pass PS Poll frames, if PROMISC_IN_BSS is not set then only - * those addressed to this station. + * @FIF_PSPOLL: pass PS Poll frames * * @FIF_PROBE_REQ: pass probe request frames */ enum ieee80211_filter_flags { - FIF_PROMISC_IN_BSS = 1<<0, FIF_ALLMULTI = 1<<1, FIF_FCSFAIL = 1<<2, FIF_PLCPFAIL = 1<<3, @@ -2661,9 +2890,9 @@ enum ieee80211_reconfig_type { * Returns zero if statistics are available. * The callback can sleep. * - * @get_tkip_seq: If your device implements TKIP encryption in hardware this - * callback should be provided to read the TKIP transmit IVs (both IV32 - * and IV16) for the given key from hardware. + * @get_key_seq: If your device implements encryption in hardware and does + * IV/PN assignment then this callback should be provided to read the + * IV/PN for the given key from hardware. * The callback must be atomic. * * @set_frag_threshold: Configuration of fragmentation threshold. Assign this @@ -2844,8 +3073,9 @@ enum ieee80211_reconfig_type { * @set_bitrate_mask: Set a mask of rates to be used for rate control selection * when transmitting a frame. Currently only legacy rates are handled. * The callback can sleep. - * @rssi_callback: Notify driver when the average RSSI goes above/below - * thresholds that were registered previously. The callback can sleep. + * @event_callback: Notify driver about any event in mac80211. See + * &enum ieee80211_event_type for the different types. + * The callback must be atomic. * * @release_buffered_frames: Release buffered frames according to the given * parameters. In the case where the driver buffers some frames for @@ -2993,6 +3223,8 @@ enum ieee80211_reconfig_type { * response template is provided, together with the location of the * switch-timing IE within the template. The skb can only be used within * the function call. + * + * @wake_tx_queue: Called when new packets have been added to the queue. */ struct ieee80211_ops { void (*tx)(struct ieee80211_hw *hw, @@ -3059,8 +3291,9 @@ struct ieee80211_ops { struct ieee80211_vif *vif); int (*get_stats)(struct ieee80211_hw *hw, struct ieee80211_low_level_stats *stats); - void (*get_tkip_seq)(struct ieee80211_hw *hw, u8 hw_key_idx, - u32 *iv32, u16 *iv16); + void (*get_key_seq)(struct ieee80211_hw *hw, + struct ieee80211_key_conf *key, + struct ieee80211_key_seq *seq); int (*set_frag_threshold)(struct ieee80211_hw *hw, u32 value); int (*set_rts_threshold)(struct ieee80211_hw *hw, u32 value); int (*sta_add)(struct ieee80211_hw *hw, struct ieee80211_vif *vif, @@ -3141,9 +3374,9 @@ struct ieee80211_ops { bool (*tx_frames_pending)(struct ieee80211_hw *hw); int (*set_bitrate_mask)(struct ieee80211_hw *hw, struct ieee80211_vif *vif, const struct cfg80211_bitrate_mask *mask); - void (*rssi_callback)(struct ieee80211_hw *hw, - struct ieee80211_vif *vif, - enum ieee80211_rssi_event rssi_event); + void (*event_callback)(struct ieee80211_hw *hw, + struct ieee80211_vif *vif, + const struct ieee80211_event *event); void (*allow_buffered_frames)(struct ieee80211_hw *hw, struct ieee80211_sta *sta, @@ -3224,6 +3457,9 @@ struct ieee80211_ops { void (*tdls_recv_channel_switch)(struct ieee80211_hw *hw, struct ieee80211_vif *vif, struct ieee80211_tdls_ch_sw_params *params); + + void (*wake_tx_queue)(struct ieee80211_hw *hw, + struct ieee80211_txq *txq); }; /** @@ -3305,14 +3541,15 @@ enum ieee80211_tpt_led_trigger_flags { }; #ifdef CONFIG_MAC80211_LEDS -char *__ieee80211_get_tx_led_name(struct ieee80211_hw *hw); -char *__ieee80211_get_rx_led_name(struct ieee80211_hw *hw); -char *__ieee80211_get_assoc_led_name(struct ieee80211_hw *hw); -char *__ieee80211_get_radio_led_name(struct ieee80211_hw *hw); -char *__ieee80211_create_tpt_led_trigger(struct ieee80211_hw *hw, - unsigned int flags, - const struct ieee80211_tpt_blink *blink_table, - unsigned int blink_table_len); +const char *__ieee80211_get_tx_led_name(struct ieee80211_hw *hw); +const char *__ieee80211_get_rx_led_name(struct ieee80211_hw *hw); +const char *__ieee80211_get_assoc_led_name(struct ieee80211_hw *hw); +const char *__ieee80211_get_radio_led_name(struct ieee80211_hw *hw); +const char * +__ieee80211_create_tpt_led_trigger(struct ieee80211_hw *hw, + unsigned int flags, + const struct ieee80211_tpt_blink *blink_table, + unsigned int blink_table_len); #endif /** * ieee80211_get_tx_led_name - get name of TX LED @@ -3326,7 +3563,7 @@ char *__ieee80211_create_tpt_led_trigger(struct ieee80211_hw *hw, * * Return: The name of the LED trigger. %NULL if not configured for LEDs. */ -static inline char *ieee80211_get_tx_led_name(struct ieee80211_hw *hw) +static inline const char *ieee80211_get_tx_led_name(struct ieee80211_hw *hw) { #ifdef CONFIG_MAC80211_LEDS return __ieee80211_get_tx_led_name(hw); @@ -3347,7 +3584,7 @@ static inline char *ieee80211_get_tx_led_name(struct ieee80211_hw *hw) * * Return: The name of the LED trigger. %NULL if not configured for LEDs. */ -static inline char *ieee80211_get_rx_led_name(struct ieee80211_hw *hw) +static inline const char *ieee80211_get_rx_led_name(struct ieee80211_hw *hw) { #ifdef CONFIG_MAC80211_LEDS return __ieee80211_get_rx_led_name(hw); @@ -3368,7 +3605,7 @@ static inline char *ieee80211_get_rx_led_name(struct ieee80211_hw *hw) * * Return: The name of the LED trigger. %NULL if not configured for LEDs. */ -static inline char *ieee80211_get_assoc_led_name(struct ieee80211_hw *hw) +static inline const char *ieee80211_get_assoc_led_name(struct ieee80211_hw *hw) { #ifdef CONFIG_MAC80211_LEDS return __ieee80211_get_assoc_led_name(hw); @@ -3389,7 +3626,7 @@ static inline char *ieee80211_get_assoc_led_name(struct ieee80211_hw *hw) * * Return: The name of the LED trigger. %NULL if not configured for LEDs. */ -static inline char *ieee80211_get_radio_led_name(struct ieee80211_hw *hw) +static inline const char *ieee80211_get_radio_led_name(struct ieee80211_hw *hw) { #ifdef CONFIG_MAC80211_LEDS return __ieee80211_get_radio_led_name(hw); @@ -3410,7 +3647,7 @@ static inline char *ieee80211_get_radio_led_name(struct ieee80211_hw *hw) * * Note: This function must be called before ieee80211_register_hw(). */ -static inline char * +static inline const char * ieee80211_create_tpt_led_trigger(struct ieee80211_hw *hw, unsigned int flags, const struct ieee80211_tpt_blink *blink_table, unsigned int blink_table_len) @@ -4091,40 +4328,6 @@ void ieee80211_aes_cmac_calculate_k1_k2(struct ieee80211_key_conf *keyconf, u8 *k1, u8 *k2); /** - * struct ieee80211_key_seq - key sequence counter - * - * @tkip: TKIP data, containing IV32 and IV16 in host byte order - * @ccmp: PN data, most significant byte first (big endian, - * reverse order than in packet) - * @aes_cmac: PN data, most significant byte first (big endian, - * reverse order than in packet) - * @aes_gmac: PN data, most significant byte first (big endian, - * reverse order than in packet) - * @gcmp: PN data, most significant byte first (big endian, - * reverse order than in packet) - */ -struct ieee80211_key_seq { - union { - struct { - u32 iv32; - u16 iv16; - } tkip; - struct { - u8 pn[6]; - } ccmp; - struct { - u8 pn[6]; - } aes_cmac; - struct { - u8 pn[6]; - } aes_gmac; - struct { - u8 pn[6]; - } gcmp; - }; -}; - -/** * ieee80211_get_key_tx_seq - get key TX sequence counter * * @keyconf: the parameter passed with the set key @@ -4343,13 +4546,33 @@ void ieee80211_sched_scan_stopped(struct ieee80211_hw *hw); * haven't been re-added to the driver yet. * @IEEE80211_IFACE_ITER_RESUME_ALL: During resume, iterate over all * interfaces, even if they haven't been re-added to the driver yet. + * @IEEE80211_IFACE_ITER_ACTIVE: Iterate only active interfaces (netdev is up). */ enum ieee80211_interface_iteration_flags { IEEE80211_IFACE_ITER_NORMAL = 0, IEEE80211_IFACE_ITER_RESUME_ALL = BIT(0), + IEEE80211_IFACE_ITER_ACTIVE = BIT(1), }; /** + * ieee80211_iterate_interfaces - iterate interfaces + * + * This function iterates over the interfaces associated with a given + * hardware and calls the callback for them. This includes active as well as + * inactive interfaces. This function allows the iterator function to sleep. + * Will iterate over a new interface during add_interface(). + * + * @hw: the hardware struct of which the interfaces should be iterated over + * @iter_flags: iteration flags, see &enum ieee80211_interface_iteration_flags + * @iterator: the iterator function to call + * @data: first argument of the iterator function + */ +void ieee80211_iterate_interfaces(struct ieee80211_hw *hw, u32 iter_flags, + void (*iterator)(void *data, u8 *mac, + struct ieee80211_vif *vif), + void *data); + +/** * ieee80211_iterate_active_interfaces - iterate active interfaces * * This function iterates over the interfaces associated with a given @@ -4364,11 +4587,16 @@ enum ieee80211_interface_iteration_flags { * @iterator: the iterator function to call * @data: first argument of the iterator function */ -void ieee80211_iterate_active_interfaces(struct ieee80211_hw *hw, - u32 iter_flags, - void (*iterator)(void *data, u8 *mac, - struct ieee80211_vif *vif), - void *data); +static inline void +ieee80211_iterate_active_interfaces(struct ieee80211_hw *hw, u32 iter_flags, + void (*iterator)(void *data, u8 *mac, + struct ieee80211_vif *vif), + void *data) +{ + ieee80211_iterate_interfaces(hw, + iter_flags | IEEE80211_IFACE_ITER_ACTIVE, + iterator, data); +} /** * ieee80211_iterate_active_interfaces_atomic - iterate active interfaces @@ -5194,30 +5422,13 @@ int ieee80211_reserve_tid(struct ieee80211_sta *sta, u8 tid); void ieee80211_unreserve_tid(struct ieee80211_sta *sta, u8 tid); /** - * ieee80211_ie_split - split an IE buffer according to ordering - * - * @ies: the IE buffer - * @ielen: the length of the IE buffer - * @ids: an array with element IDs that are allowed before - * the split - * @n_ids: the size of the element ID array - * @offset: offset where to start splitting in the buffer - * - * This function splits an IE buffer by updating the @offset - * variable to point to the location where the buffer should be - * split. + * ieee80211_tx_dequeue - dequeue a packet from a software tx queue * - * It assumes that the given IE buffer is well-formed, this - * has to be guaranteed by the caller! - * - * It also assumes that the IEs in the buffer are ordered - * correctly, if not the result of using this function will not - * be ordered correctly either, i.e. it does no reordering. + * @hw: pointer as obtained from ieee80211_alloc_hw() + * @txq: pointer obtained from station or virtual interface * - * The function returns the offset where the next part of the - * buffer starts, which may be @ielen if the entire (remainder) - * of the buffer should be used. + * Returns the skb if successful, %NULL if no frame was available. */ -size_t ieee80211_ie_split(const u8 *ies, size_t ielen, - const u8 *ids, int n_ids, size_t offset); +struct sk_buff *ieee80211_tx_dequeue(struct ieee80211_hw *hw, + struct ieee80211_txq *txq); #endif /* MAC80211_H */ |